31023
76
Zoom out
Zoom in
Previous page
1/88
Next page
76
EN
VIDEO NAVIGATION
CORRECTIVE ACTION
Tape information cannot be shown if it
has not been recorded on this VCR.
Video Navigation cannot work
correctly on a tape if it has more than
one tape number. If this happens, fast-
forward the tape up to its end, eject it,
and try it again.
Check the remaining memory ( pg.
51). If it is full, delete unnecessary
Video Navigation information. ( pg.
51).
SYMPTOM
1. Tape infomation screen does not
appear for the currently inserted
tape.
2. The VCR cannot search for the
correct program.
3. “MEMORY FULL” appears on the
screen when you try to start
recording.
POSSIBLE CAUSE
The current tape inserted has not
been recorded on this VCR.
Two (or more) tape numbers are
recorded on one tape.
The VCR’s memory for Video
Navigation is fully recorded.
ATTENTION
This VCR contains microcomputers. External electronic noise or interference can cause microcomputer to malfunction. If the
VCR does not operate correctly switch its power off and unplug the AC power cord from the AC supply. Wait for a while and
then plug the power back in. Eject and check the condition of the cassette. If everything appears normal, you can operate the
VCR as usual.
MOISTURE CONDENSATION
Moisture in the air will condense on the VCR when you move it from a cold place to a warm place, or under
extremely humid conditions—just as water droplets form on the surface of a glass filled with cold liquid. Moisture
condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the
VCR turned on for a few hours to evaporate the moisture before inserting a tape.
ABOUT HEAD CLEANING
Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or
interrupted. Be sure to contact your nearest JVC dealer if such troubles occur.
TROUBLESHOOTING (cont.)
OTHER PROBLEMS
CORRECTIVE ACTION
If you need the skipped channels,
restore them ( pg. 14).
Press PAUSE ( 8 ) to pause the
recording, change channels, then
press PLAY ( 3 ) to resume recording.
Reset the correct brand codes ( pg.
70, 71 or 72).
Select a different host channel during
Semiauto Clock Set ( pg. 11), or
perform Manual Clock Set ( pg. 12).
SYMPTOM
1. When scanning channels, some of
them are skipped over.
2. The channel cannot be changed.
3. The Remote will not operate your
TV or cable box or DBS receiver.
4. Even though Auto or Semiauto
Clock Set has been performed, the
clock is incorrect.
POSSIBLE CAUSE
Those channels have been preset to
be skipped.
Recording is in progress.
The brand codes are set incorrectly.
The clock setting data received from
the host channel is incorrect.
HR-S9800U-EN74-88 00.3.29, 7:31 PM76
76


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC HRS9800U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC HRS9800U in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info