31023
74
Zoom out
Zoom in
Previous page
1/88
Next page
74
EN
TROUBLESHOOTING
Before requesting service, use this chart and see if you can repair the trouble yourself. Small problems are often easily
corrected, and this can save you the trouble of sending your VCR off for repair.
POSSIBLE CAUSE
The AC power cord is disconnected.
The VCR is in the timer recording
standby mode with “AUTO TIMER”
set to “OFF” ( pg. 57).
The child lock function is activated.
The batteries are discharged.
SYMPTOM
1. The power will not come on.
2. The clock works, but the VCR’s
power will not come on.
3. The Remote will not function.
CORRECTIVE ACTION
Connect the AC power cord.
Press TIMER to disengage.
Press and hold POWER on the
Remote for more than seven seconds
to release the child lock function (
pg. 62).
Replace the dead batteries with new
ones.
SYMPTOM
1. The cassette gets stuck partway
during loading, and is ejected.
CORRECTIVE ACTION
Make sure the cassette’s window is
facing up, the rear label side is facing
you and the arrow on the front of the
cassette is pointing towards the VCR.
Then insert the cassette.
POSSIBLE CAUSE
The cassette was inserted incorrectly.
SYMPTOM
1. The tape is running but the picture
will not appear.
2. Breaks are noticeable in Hi-Fi
sound track.
3. The playback picture is blurred or
interrupted, even though TV
broadcasts are clear.
4. The Hi-Fi sound cannot be heard.
POSSIBLE CAUSE
If the RF connection ( pg. 7) is
used to view the picture, the
channel on the TV is set incorrectly.
If the AV connection ( pg. 7) is
used to view the picture, the TV
receiver is set to the wrong mode.
Automatic tracking is engaged.
The video heads may be dirty.
Audio Monitor setting is incorrect.
CORRECTIVE ACTION
Select channel 3 or 4 on the TV.
Select the AV mode on the TV.
Disengage auto tracking and adjust
the tracking manually ( pg. 25).
The heads must be cleaned. Consult
your JVC dealer.
Set Audio Monitor to “HI-FI”
( pg. 25 or 59).
CORRECTIVE ACTION
Insert a cassette.
Remove the cassette and cover the
hole with adhesive tape, or load a
cassette on which the record safety
tab is intact.
Select the appropriate channel on the
VCR.
Connect the components correctly
( pg. 64 – 69) or check “REAR AUX
INPUT” and “FRONT AUX INPUT”
setting ( pg. 60).
Make sure the power to all units is on.
Select the appropriate input mode on
the recording VCR.
POSSIBLE CAUSE
There is no cassette loaded.
The loaded cassette has had its
record safety tab removed.
The VCR has been set to “L-1” or “F-
1” input mode by mistake.
The components have been
incorrectly connected, or correct
video connector (S VIDEO or
VIDEO) is not selected.
The power to one or more of the
units has not been turned on.
The recording VCR’s input mode has
been set incorrectly.
SYMPTOM
1. Recording will not start.
2. TV broadcasts will not be recorded
properly.
3. Tape-to-tape editing will not work.
POWER
TAPE TRANSPORT
PLAYBACK
RECORDING
HR-S9800U-EN74-88 00.3.29, 7:31 PM74
74


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC HRS9800U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC HRS9800U in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info