138393
53
Zoom out
Zoom in
Previous page
1/72
Next page
Masterpage:Right-No-Heading
53
Filename [XV48EK_10Subsidiary.fm]
Page 53 November 18, 2004 10:44 pm
* The default setting is bold in the table below.
8 B.E.S.T.ON / OFF
You can set the B.E.S.T. (Biconditional Equalised Signal Tracking)
system to “ON” or “OFF.” (
pg. 23)
NOTES:
When watching a tape recorded with “B.E.S.T.” set to “ON,” it
is recommended that you leave B.E.S.T. on during playback as
well.
When watching a rental tape or one recorded on another
video recorder, or when using this unit as the player for
editing, set B.E.S.T. to your preference.
The B.E.S.T. system works for both SP and LP modes only after
a tape has been inserted and the Record mode is first initiated.
It does not work during recording.
The B.E.S.T. system does not work while Automatic Satellite
Programme Recording is in progress. (
pg. 28)
In the case of timer recordings, the B.E.S.T. system works
before recording is initiated.
Once the cassette is ejected, the B.E.S.T. data is cancelled. The
next time the cassette is used for recording, B.E.S.T. is re-
performed.
Pressing the unit’s 7 button while “BEST” is displayed does
not start Instant Timer Recording. (
pg. 22)
8 PICTURE CONTROLAUTO / EDIT / SOFT
This feature helps you to adjust the playback picture quality
according to your preference. Normally select “AUTO.
AUTO: Provides the optimised picture benefits of the B.E.S.T.
Picture System.
EDIT: Minimizes picture degradation during editing (recording
and playback).
SOFT: Reduces image coarseness when viewing overplayed
tapes containing a lot of noise.
NOTES:
When you select “EDIT” or “SOFT,” the selected mode will not
change until you select another mode.
When you select “EDIT” to dub tapes, be sure to select
AUTO” after you finish dubbing the tapes.
When “B.E.S.T.” is “OFF”, “PICTURE CONTROL” switches
automatically from “AUTO” to “NORM.
8 O.S.D.ON / OFF
When this function is set to “ON,” various operational indicators
appear on the TV screen.
NOTES:
When you use this unit as the source player for editing, be sure
to set “O.S.D.” to “OFF” before starting.
During playback, the operation mode indicators may be
disturbed depending on the type of tape being used.
8 DIRECT RECON / OFF
When this function is set to “ON,” you can easily start recording
the programme that you are watching on your TV. Press and hold
7 and press 4 on the remote control, or press 7 on the unit.
NOTES:
When you use the Direct Rec function, be sure to use a TV
offering T-V LINK, etc. and connect a fully-wired 21-pin
SCART cable between the unit and the TV. (
pg. 11)
If “DIRECT REC” is set to “OFF,” the 7 button functions as
described in “Basic Recording” (
pg. 21).
During Direct Rec, “– –” appears on the front display panel.
When “DIRECT REC” is set to “ON,” if you press any button
just after pressing 7 on the unit (or 7 and 4 on the remote
control), the unit may not function properly.
8 AUTO SP]LP TIMER — ON / OFF
When this function is set to “ON”, the unit automatically
switches to LP mode to allow complete recording if there is not
enough tape to record the entire programme while timer-
recording in SP mode.
For Example:
Recording a programme of 210 minutes in length onto a 180-
minute tape
Make sure you set this function to “ON, before the timer-
recording starts.
NOTES:
If you have programmed the unit to timer-record 2 or more
programmes, the second programme and those thereafter may
not fit on the tape if you set “AUTO SP]LP TIMER” to “ON.
In this case, make sure the mode is not engaged, then set the
tape speed manually during timer programming.
In order to ensure that the recording fits on the tape, this
feature may leave a slight non-recorded section at the end of
the tape.
There may be some noise and sound disturbance at the point
on the tape where the unit switches from SP to LP mode.
The Auto SP
]LP Timer feature is not available during ITR
(Instant Timer Recording), and the feature will not work
properly with any tapes longer than E-180, or with some tapes
of shorter lengths.
If you perform timer recording with both PDC and the Auto
SP
]LP Timer activated, and the programme goes beyond its
originally scheduled length, there may be times when the
programme cannot be recorded in its entirety.
Total 210 minutes
Approximately 150 minutes Approximately 60 minutes
SP mode LP mode
XV48EK_01.book Page 53 Thursday, November 18, 2004 10:45 PM
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC hr xv48ex at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC hr xv48ex in the language / languages: English, German as an attachment in your email.

The manual is 3,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info