454021

JVC HR-VP48U Manual

37
Zoom out
Zoom in
Previous page
1/48
Next page
EN
37
CORRECTIVE ACTION
Set the clock and/or timer correctly.
Press TIMER and check to make sure
that ‰ appears on the front display
panel.
Re-perform the set-up procedures.
Make sure you have compensated for
guide channel and VCR or cable box
channel number mismatches
(੬ pg. 26).
Timer programing cannot be performed
when timer recording is in progress.
Wait until it finishes.
Load a cassette with the record safety
tab intact, or with the hole covered
with adhesive tape.
Remove the cassette and cover its
hole with adhesive tape, or replace it
with a cassette on which the safety
tab is intact.
Check the programed data and set
again if necessary, then press TIMER
again.
The program may not have been
recorded in its entirety. Next time be
sure you have enough time on the
tape to record the entire broadcast.
Re-perform the VCR Plus+ setup
procedure (੬ pg. 26).
Wait until a space in memory clears,
or cancel unnecessary program
information (੬ pg. 30).
SYMPTOM
1. Timer recording will not work.
2. Timer programing will not work.
3. ‰ and ] on the front display
panel will not stop blinking.
4. The cassette is automatically
ejected, and ‰ and ] on the
front display panel will not stop
blinking.
5. ‰ blinks for 10 seconds and the
timer mode is disengaged.
6. The cassette is automatically
ejected, the power shuts off and ‰
and ] will not stop blinking.
7. You moved, and now VCR Plus+
does not work properly.
8. “PROGRAM FULL” is displayed on
the screen.
POSSIBLE CAUSE
● The clock and/or the timer have
been set incorrectly.
● The timer is not engaged.
● The VCR has not been set up properly.
● Timer recording is in progress.
● The timer is engaged but there is no
cassette loaded.
● The loaded cassette has had its
record safety tab removed.
● TIMER has been pressed when there
are no programs in memory, or the
timer recording program has not
been set correctly.
● The tape reaches its end during
timer recording.
● The receivable stations in the new
area are received on different
channels than those in the previous
area.
● All 8 programs of the VCR’s timer
memory are used.
TIMER RECORDING
OTHER PROBLEMS
CORRECTIVE ACTION
If you need the skipped channels,
restore them (੬ pg. 14).
Press PAUSE ( 8 ) to pause the
recording, change channels, then
press PLAY ( 3 ) to resume recording.
Select a different host channel during
Semiauto Clock Set (੬ pg. 11), or
perform Manual Clock Set (੬ pg. 12).
SYMPTOM
1. When scanning channels, some of
them are skipped over.
2. The channel cannot be changed.
3. Even though Auto or Semiauto
Clock Set has been performed, the
clock is incorrect.
POSSIBLE CAUSE
● Those channels have been preset to
be skipped.
● Recording is in progress.
● The clock setting data received from
the host channel is incorrect.
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC HR-VP48U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC HR-VP48U in the language / languages: English as an attachment in your email.

The manual is 1,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info