658631

JVC HR-S9900U Manual

69
Zoom out
Zoom in
Previous page
1/88
Next page
EN 69
Make connections
Connect an audio/video cable between the VCR’s
audio/video input connectors and the other
component’s audio/video output connectors.
Prepare tapes
Load the source tape on the other VCR, and the
tape to be edited on this VCR.
Select input mode
Select “F-1” — when connecting the other
component to the audio/video input
connectors on the front panel.
Select “L-1” — when connecting the other
component to the audio/video input
connectors on the rear panel.
On the front panel:
Press CH5∞.
On the Remote:
Press the Number key “0 (AUX)” or CH +/–.
Select video input terminal
Follow the procedure described on pages 56 and
60.
When using S VIDEO terminal, set “FRONT AUX
INPUT” (or “REAR AUX INPUT” if you use the
connectors on the rear) to “S-VIDEO”.
When using VIDEO terminal, set “FRONT AUX
INPUT” (or “REAR AUX INPUT”) to “VIDEO”.
Select edit mode
Set the edit mode to “ON” for the VCRs if such a
mode is equipped.
● On this VCR, set “PICTURE CONTROL” to
“EDIT” by following the procedure described
on pages 56 and 57.
Locate end point
Press PLAY ( 3 ) to start playback.
Press PAUSE ( 8 ) when you find the end of
the scene for which you want to edit.
Press C. RESET so that the counter reading
becomes “0:00:00”.
NOTE:
You can also use
FF
( ), the
TIME SCAN SHUTTLE
ring on the front panel, and the
JOG/SHUTTLE
ring on
the Remote to locate the end point (See “Special Effect
Playback”:
墌
pg. 34) .
Locate start point
Use REW ( ), the TIME SCAN SHUTTLE ring
on the front panel, or JOG/SHUTTLE ring on the
Remote to reverse the tape. (See “Special Effect
Playback”: 墌 pg. 34.)
When you find the beginning of the scene you
want to edit, press PAUSE ( 8 ).
Activate editing mode
For Inset Editing:
Press INSERT on the front panel.
For AV Dubbing:
Press INSERT, then press A. DUB on the front
panel.
● Make sure that the recording format (VHS, S-
VHS or S-VHS ET) on the VCR is the same as
that of the original recording on the tape.
● During Insert Editing pause mode (
, and
light up on the front display panel.)
● During AV Dubbing pause mode (
and
blink, and lights up on the front display
panel.)
Start editing
Press PLAY ( 3 ) on this VCR, and start playback
on the other component at the same time.
● During Insert Editing mode ( and light up
on the front display panel.)
● During AV Dubbing mode ( and blink on
the front display panel.)
● When the counter reading becomes “0:00:00”,
editing automatically stops, and the VCR starts
normal playback.
To stop editing any time during recording
Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 )
on the front panel.
NOTES:
●
Be sure to select “AUTO” for “PICTURE CONTROL” (or
“NORM” when “VIDEO CALIBRATION” is set to “OFF”) after
you finish editing the tapes (
墌
pg. 56 and 57).
●
Editing cannot be performed on a tape with its record safety
tab removed.
●
The recording speed (SP/EP) is determined by the previous
recording to be replaced. If the recording speed changes on
the tape to be edited while editing the tape, the inserted
picture will be distorted where the recording speed changes.
●
When you edit a tape, a small portion of the recording
preceding to the editing start point will be erased from the
edited tape.
… 69 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC HR-S9900U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC HR-S9900U in the language / languages: English as an attachment in your email.

The manual is 2,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info