658628
6
Zoom out
Zoom in
Previous page
1/76
Next page
6 EN
INSTALLING YOUR NEW VCR
Connections
Antenna or Cable
Flat Feeder
Basic Connections
CHECK CONTENTS
1
Make sure the package contains all of the accessories
listed in “SPECIFICATIONS” (Z pg. 73).
SITUATE VCR
2
Place the VCR on a stable, horizontal surface.
CONNECT VCR TO TV
3
The connection method you use depends on the type of
TV you have.
RF Connection
To Connect To A TV With NO AV Input Terminals . . .
a– Disconnect the TV antenna from the TV.
b– Connect the TV antenna cable to the ANTENNA
IN jack on the rear of the VCR.
c– Connect the supplied RF cable between the TV OUT
jack on the rear of the VCR and the TV’s antenna
terminal. Set TV on CH3 or CH4 corresponding to the
CH3 – CH4 switch setting on the back of the VCR.
AV Connection
To Connect To A TV With AV Input Terminals . . .
a– Connect the antenna, VCR and TV as shown in
the illustration.
b– Connect an Audio/Video Cable between the
AUDIO OUT and VIDEO OUT jacks on the rear of
the VCR and the AV IN jacks on the TV. Set your
TV in video input mode or A/V input mode. Refer
to the TV Instruction Manual.
S-VIDEO Connection
If you have a TV with S-VIDEO input terminals, see
"S-VIDEO Connection" on page 7.
CONNECT VCR TO
POWER SOURCE
4
Connect the power plug to an AC outlet.
The clock will automatically be set when the antenna
is connected and when the AC is first connected to
the VCR (Z pg. 8).
(If "Auto" is displayed on the front display panel
before the VCR is powered on, the clock is being set
automatically. Wait for the time to be displayed on
the front display panel before powering on the VCR.)
FINAL PREPARATION FOR
USE
5
Power on the VCR and select the VCR channel (3 or 4)
by setting the switch on the rear of the VCR as shown in
the illustration.
You can now perform simple playback (Z pg. 26) or
simple recording (Z pg. 27).
Coaxial Cable
AC Power
Cord
Back of VCR
AC
Outlet
ANTENNA-
IN (Antenna
or Cable
input)
75 ohm terminal
TV
Matching Transformer
(Not supplied)
TV OUT
Audio/Video
Cable (supplied)
RF Cable
(supplied)
NOTES:
The VCR channel is the channel on the TV which will display
the audio and video signals from the VCR. The VCR's CH3-
CH4 switch, on the back of the VCR, sets the VCR channel to
CH3 or CH4.
The CH3–CH4 switch is preset to the CH3 position.
Set to CH4 if CH3 is used for broadcasting in your area and
set the channel on the TV to correspond to the VCR's CH3–
CH4 switch setting.
If RF connection to TV is used, when switching from VIDEO to TV
mode and from TV to VIDEO it may be necessary to issue a CH
UP and then CH DOWN on TV to obtain a good quality picture.
Even if you are using AV cables to connect your VCR to your TV,
you must also connect it using the RF cable. This will ensure that
you can record one show while watching another (
Z
pg. 41).
For full identification of the VCR's rear panel, refer to the
Index (REAR VIEW
Z
pg. 71).
CH3 CH4
Back of VCR
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC HR-S9400U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC HR-S9400U in the language / languages: English as an attachment in your email.

The manual is 2,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info