658623
40
Zoom out
Zoom in
Previous page
1/68
Next page
40
EN
* The default setting is bold in the table below.
When this function is set to “ON”, the VCR automatically switches to EP
mode to allow complete recording if there is not enough tape to record
the entire program while timer-recording in SP mode.
For Example . . .
Recording a program of 140 minutes in length onto a 120-minute tape
Make sure you set this function to “ON” before the timer-recording starts.
NOTES:
If you have programed the VCR to timer-record 2 or more programs, the second
program and those thereafter may not fit on the tape with this function set to
“ON”. In this case, do not use this function, but change the tape speed
manually during timer programing.
In order to ensure that the recording fits on the tape, this function may leave a
slight non-recorded portion at the end of the tape.
There may be some noise and sound disturbance where the tape speed switches
from SP to EP mode on the tape.
This function is not available during ITR (Instant Timer Recording), and will not
work properly on the following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-
120.
When this function is set to “ON”, edge correction to the luminance
signal is performed to enhance details. Normally set this function to
“ON”.
NOTES:
Depending on the type of tape being used, picture quality may be better with
“DIGITAL R3” set to “OFF”.
If you use this VCR as the playback VCR for editing, be sure to set “DIGITAL
R3” to “OFF” before starting.
When this function is set to “ON”, you can automatically correct vertical
vibrations in the picture when playing back unstable recordings made on
another VCR.
NOTES:
When you finish viewing a tape, be sure to set this function to “OFF”.
Regardless of the setting, this function has no effect during recording and during
special effects playback.
The on-screen display may jitter vertically when this function is set to “ON”.
To watch recordings with close-caption, set this function to “OFF”.
Video Stabilizer and Digital TBC/NR cannot be used at the same time. If you
activate Digital TBC/NR when “VIDEO STABILIZER” is set to “ON”, Video
Stabilizer will be automatically turned “OFF”.
When this function is set to “ON”, the TV screen becomes all blue in the
following cases:
When receiving a channel not in use.
When stopping playback.
NOTE:
When you want to receive an unstable channel with poor signals, set this function
to “OFF”.
When this function is set to “ON”;
If a SAP program is received, the SAP audio is recorded on both the
normal and Hi-Fi tracks. The main audio is not recorded.
If a non-SAP program is received, the main audio is recorded on both
the Hi-Fi and normal tracks.
When this function is set to “OFF”, the SAP audio cannot be recorded.
AUTO SP = EP TIMER
ON
OFF
VIDEO STABILIZER
ON
OFF
Approximately 110 minutes
SP mode
Approximately 30 minutes
EP mode
BLUE BACK
ON
OFF
OTHER USEFUL FUNCTIONS (cont.)
2ND AUDIO RECORD
ON
OFF
DIGITAL R3
ON
OFF
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC HR-S7800U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC HR-S7800U in the language / languages: English as an attachment in your email.

The manual is 2,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info