658623
18
Zoom out
Zoom in
Previous page
1/68
Next page
18
EN
INITIAL SETTINGS (cont.)
The following procedure is required if you receive satellite
channels through a DBS (Direct Broadcast Satellite)
receiver. The Controller allows the VCR to automatically
switch the DBS receivers channels during timer recording.
NOTES:
The VCR can automatically change the DBS receiver
channels using the Controller when the VCR has been
programed using Express timer programing (
pg. 34).
Because satellite programing does not use PlusCode, the
Controller cannot change the DBS receiver channels during
VCR Plus+ timer recording.
If a cable box is also used, it is recommended that you connect
the DBS receiver to your VCR’s audio/video input connectors
and the cable box to your VCR’s antenna input terminal.
Installing Controller
1
Situate Controller
Place the Controller so that its transmitter is
facing the DBS receiver’s remote sensor.
Make sure the path between the Controller and
the DBS receivers remote sensor is not
blocked.
2
Attach Controller
Fix securely using the adhesive strip attached on
the back of the Controller.
3
Connect DBS receiver to VCR
If your DBS receiver does not have audio/
video output connectors
Connect the RF output terminal on the DBS
receiver to the ANTENNA IN terminal on the
rear of your VCR.
If your DBS receiver has audio/video output
connectors
Connect an audio/video cable between the
AUDIO/VIDEO IN connectors on the rear of
the VCR and the audio/video output connectors
on the DBS receiver.
NOTE:
When connecting your DBS receiver, refer to its
instruction manual.
4
Connect Controller to VCR
Connect the Controller to the CABLE BOX
Controller connector on the rear panel.
DBS Receiver
Control Setting
Suggested location
Place the DBS (Direct Broadcast Satellite) receiver on top
of the VCR. Attach the VCR’s Controller to the top of the
VCR with the Controllers transmitter pointed towards
the DBS receivers remote sensor.
ATTENTION:
The Controller can also control a cable box. If both a DBS
receiver and a cable box are used, position the Controller so its
signal reaches the remote sensors on both the DBS receiver and
cable box.
How to control the DBS receiver
This VCR has two separate methods to control your DBS receiver.
The VCR’s wireless Remote can control your DBS receiver. This eliminates the need for a separate DBS receivers Remote.
The VCR’s Controller can also control your DBS receiver. This allows the VCR to change your DBS receivers channel number
during timer-recording.
Each method must be set up separately. To set up the VCR’s Remote, refer to page 52. To set up the Controller, go to page 19.
CABLE
BOX
DBS receiver
DBS receiver
Your VCR
Controller
(suggested
locations)
Transmitter
Your VCR
To
ANTENNA IN
To
AUDIO/
VIDEO IN
To
RF output
To
Audio/Video
output
or
Controller
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC HR-S7800U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC HR-S7800U in the language / languages: English as an attachment in your email.

The manual is 2,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info