589974
57
Zoom out
Zoom in
Previous page
1/60
Next page
subsidiary information 57
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
RECORDING
1. Recording cannot be started.
2. TV broadcasts cannot be
recorded.
3. Tape-to-tape editing is not
possible.
4. Camcorder recording is not
possible.
5. U and , on the display panel
won’t stop blinking.
TIMER RECORDING
1. Timer recording won’t work.
2. Timer programming is not
possible.
3. c on the display panel won’t
stop blinking.
4. c, U and , on the display
panel won’t stop blinking.
5. c blinks for 10 seconds and the
Timer mode is disengaged.
6. The VIDEO Plus+ system does
not timer record properly.
There is no cassette loaded, or
the cassette loaded has had its
record safety tab removed.
L-1, L-2 or F-1 has been selected
as the input mode.
The source (another VCR,
camcorder) has not been
properly connected.
All necessary power switches
have not been turned on.
The input mode is not correct.
The camcorder has not been
properly connected.
The input mode is not correct.
The end of the tape was
reached during Recording.
The clock and/or the timer
have been set incorrectly.
The timer is not engaged.
Timer recording is in progress.
The timer is engaged but
theres no cassette loaded.
The loaded cassette has had its
record safety tab removed.
The end of the tape was
reached during timer recording.
c has been pressed when
there are no programs in
memory, or the timer record
information has been pro-
grammed incorrectly.
The VCR’s preset positions
have been set incorrectly.
Insert a cassette, or using
adhesive tape, cover the hole
where the tab was removed.
Set to the desired preset.
Confirm that the source is
properly connected.
Confirm that all units’ power
switches are turned on.
Set the input mode to L-1, L-2 or
F-1.
Confirm that the camcorder is
properly connected.
Set the input mode to L-1, L-2 or
F-1.
The programme may not have
been recorded in its entirety. Next
time make sure you have enough
time on the tape to record the
entire programme.
Re-perform the clock and/or
timer settings.
Press c and confirm that c is
displayed on the display panel.
Timer programming can’t be
performed while a timer recording
is in progress. Wait until it
finishes.
Load a cassette with the record
safety tab intact.
Remove the cassette and cover
the hole with adhesive tape, or
insert a cassette with the record
safety tab intact.
The programme may not have
been recorded in its entirety. Next
time make sure you have enough
time on the tape to record the
entire programme.
Check the programmed data and
re-programme as necessary, then
press c again.
Refer to Guide Program Numbers
( pg. 54) and re-perform the
procedure.
HR-S6955EK-EN/p53-59 3/18/02, 03:48 PM57
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC HR-S6955 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC HR-S6955 in the language / languages: English as an attachment in your email.

The manual is 1,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info