474088
11
Zoom out
Zoom in
Previous page
1/60
Next page
three step quick start 11
Check the Results
When Auto Setup finishes, you will see one of the three following examples on
the VCR display panel:
The Preset Positions and the Clock have been set successfully
Go straight to Step 3 (20:00 used as example only).
The Preset Positions have been set successfully but the Clock has not
Perform Clock Set on page 51.
Go to
Step 3.
Neither the Preset Positions or the Clock have been set successfully
Make sure the cables are connected properly to the VCR and turn
the VCR off and then on again. Try
Auto Set Up again.
Finish Off
Select the Video channel or AV mode, then make sure that all necessary stations
have been stored in the VCR’s memory by using the
PR
and
PR
buttons.
If station names (ID — pg.49) have also been stored in the VCR’s memory, the
station name will be displayed at the top left corner of the TV screen for about 5
seconds each time you select a different channel via the VCR.
The VCR is now set up. You can now use it to play and record.
IMPORTANT
re-running setup Auto Setup may not behave as described if it has already
been run on the VCR. This is because some of the information gathered on the
first Auto Setup- is retained in memory and that part of the process may be
skipped by the VCR.
bad reception In certain reception conditions, station names may not be
stored correctly, and
Guide Program Numbers may not be set properly. If this
happens, when you timer-record a TV programme using the VIDEO Plus+
system, the VCR will record a TV programme of a different station. When
programming the timer using the VIDEO Plus+ system, be sure to check that
the preset position corresponding to the broadcasting station you wish to
record has been selected ( pg.21,
VIDEO Plus+ Timer Programming).
duplicate stations You may be able to receive the same station from two
different transmitters in which case Auto Setup will detect and store both. It is
normal for one transmitter to give you a better quality picture than the other; to
delete those stations which have a poor picture
Delete A Channel on page47.
manual station setting If any of the above problems occur, refer to
pages47–48 to input station names (
Change Station Name). You can also
change station preset positions (
Change Station Preset Position).
rf connections In certain reception conditions, the Video Channel may not
be set correctly and interference may appear in the TV picture while the VCR’s
power is on. Set your Video Channel manually. ( pg.44,
Video Channel Set)
IF YOU HAVE ANY DIFFICULTY WITH THE ABOVE PROCEDURES CALL THE JVC
CUSTOMER SERVICE HOT LINE ON 0870 330 5000
:
AUDIO
0000
VPS/PDC
3
5
3
2 4
30 SEC
?
PR
PR
PR
ENTER
LP00000-000
VCR/TV
i
3
PR
PR
HR-S5965/5966EK-EN/p08-12 2/19/03, 04:08 PM11
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC HR-S5965 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC HR-S5965 in the language / languages: English as an attachment in your email.

The manual is 2,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info