136260
51
Zoom out
Zoom in
Previous page
1/56
Next page
Masterpage:Right-NoTitle0
EN
51
Filename [HRS5950EU4-EN.fm]
Page 51 December 4, 2001 5:11 pm
RECORDING
TIMER RECORDING
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
1. Recording cannot be started. There is no cassette loaded, or the
cassette loaded has had its record safety
tab removed.
Insert a cassette, or using adhesive tape,
cover the hole where the tab was
removed.
2. TV broadcasts cannot be recorded. “L-1”, “L-2”, “F-1” or “SAT” has been
selected as the input mode.
Set to the desired channel.
3. Tape-to-tape editing is not possible. The source (another video recorder,
camcorder) has not been properly
connected.
Confirm that the source is properly
connected.
All necessary power switches have not
been turned on.
Confirm that all units’ power switches are
turned on.
The input mode is not correct. Set the input mode to “L-1”, “L-2” or
“F-1”.
4. Camcorder recording is not possible. The camcorder has not been properly
connected.
Confirm that the camcorder is properly
connected.
The input mode is not correct. Set the input mode to “L-1”, “L-2” or
“F-1”.
5. ” and “
$
“ on the front display
panel won’t stop blinking.
The end of the tape was reached during
recording.
The programme may not have been
recorded in its entirety. Next time make
sure you have enough time on the tape to
record the entire programme.
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
1. Timer recording won’t work. The clock and/or the timer have been set
incorrectly.
Re-perform the clock and/or timer
settings.
The timer is not engaged. Press
#
and confirm that “
#
” is displayed
on the front display panel.
2. Timer programming is not possible. Timer recording is in progress. Timer programming can’t be performed
while a timer recording is in progress.
Wait until it finishes.
3.
#
” on the front display panel won’t
stop blinking.
The timer is engaged but there’s no
cassette loaded.
Load a cassette with the record safety tab
intact.
4.
#
”, “” and “
$
” on the front display
panel won’t stop blinking.
The loaded cassette has had its record
safety tab removed.
Remove the cassette and cover the hole
with adhesive tape, or insert a cassette
with the record safety tab intact.
The end of the tape was reached during
timer recording.
The programme may not have been
recorded in its entirety. Next time make
sure you have enough time on the tape to
record the entire programme.
5.
#
” blinks for 10 seconds and the
Timer mode is disengaged.
#
has been pressed when there are no
programs in memory, or the timer
record information has been
programmed incorrectly.
Check the programmed data and
re-program as necessary, then press
#
again.
6. The S
HOW
V
IEW
system does not
timer-record properly.
The recorder’s channel positions have
been set incorrectly.
Refer to “Guide Program Number Set”
(
pg. 49) and re-perform the procedure.
7. ” and “
$
“ on the front display
panel won’t stop blinking.
The end of the tape was reached during
Instant Timer Recording.
The programme may not have been
recorded in its entirety. Next time make
sure you have enough time on the tape to
record the entire programme.
HRS5950EU1-EN.book Page 51 Tuesday, December 4, 2001 5:32 PM
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC hr s 5950 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC hr s 5950 in the language / languages: English as an attachment in your email.

The manual is 3,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info