559741
20
Zoom out
Zoom in
Previous page
1/40
Next page
20
ENTER SHOWVIEW
NUMBER
4
Press OK, and a cursor
appears above “GUIDE
PROG”. Then, using the
NUMBER keys, input the
ShowView number (found
in most TV listings) of a
program scheduled to be
broadcast on each station
on the list from step 1,
starting at the top. If you
enter the wrong number,
press CANCEL and input the correct number.
ENTER CHANNEL POSITION
NUMBER
4
5
Press OK and the display
under “TV PROG” begins
blinking.
If the blinking number
under “TV PROG” agrees
with the channel
position . . .
. . . press OK.
If the numbers do not agree . . .
. . . input the channel position using PUSH JOG
%
or
the NUMBER keys, then press OK.
If you input the ShowView number of a program that
has already aired, “ERROR” appears on screen for a
few seconds. Input the correct ShowView number.
Repeat steps 4 and 5 as necessary.
CLOSE MENU
6
Press CH SET and selection is complete.
If you already know the Guide Prog. number for a station . . .
1– After step 3, press PUSH JOG .
The GUIDE PROG number begins blinking.
2– Enter the Guide Prog. number using the NUMBER keys or
PUSH JOG
%
, then press PUSH JOG .
The TV PROG number begins blinking.
3– Enter the channel position using the NUMBER keys or
PUSH JOG
%
, then press PUSH JOG .
Repeat 2 and 3 as necessary.
4– Press CH SET.
TIMER RECORDING(cont.)
When entering a ShowView
number for ARD
When Using A Satellite
Tuner
Preparation
1– Connect the satellite tuner to the AV2 IN/DECODER
connector on the rear of your recorder.
2– Set the AV2 SELECT switch to "AV2".
To Record Satellite Broadcasts . . .
1– Select the appropriate channel on the satellite tuner.
2– Press NUMBER key "0" to set your recorder's input mode to
"AUX2".
3– Start recording ( pg. 14, steps 3 – 6).
To Record Satellite Broadcasts Using ShowView Timer
Recording . . .
1– Perform Guide Prog. Number setting.
In step 5 in the left column, press NUMBER key "0" to set
"TV PROG" to "AUX2".
2– Perform ShowView Timer Recording ( pg. 21).
To Record Satellite Broadcasts Using Regular Timer Recording . . .
1– In step 6 on page 23, press TV PROG. +/– to set the channel
position to "AUX2".
NOTES:
During timer programming, once you have selected the
programme you wish to record from the satellite tuner, set the
system's timer. If your satellite tuner does not have a timer,
leave it switched on.
If your recorder's front panel VIDEO and/or AUDIO connec-
tors are being used, they take priority and "AUX2" cannot be
selected. Make sure no cables are connected to the front
panel connectors when performing this procedure.
12345
5
GUIDE PROG TV PROG
11
[0 – 9] =
GUIDE PROG TV PROG
250 39
[5
] =
Satellite
Tuner
Satellite Antenna
Satellite
Tuner
Ex. 1
Ex. 2
Aerial or Cable
Decoder
AV2 IN/DECODER
AV2 SELECT Switch
TV Receiver
%
%
%
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC HR-J438E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC HR-J438E in the language / languages: English as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info