476523
12
Zoom out
Zoom in
Previous page
1/16
Next page
Page 12 September 3, 2001 9:09 am
Changing Remote Control Code
This remote control is capable of transmitting two control codes;
one set to respond to A code control signals and another set to
respond to B code control signals. This remote control is preset to
send A code signals because your recorder is initially set to
respond to A code signals. You can easily modify your recorder
and the remote control to respond to B code signals. When using
two JVC recorders, set two recorders and their remote controls to
different codes, so that you can operate these recorders separately.
A
Set remote control code for remote control
A Press and hold VCR.
B Press the Number key 2.
C Press OK, and release VCR.
The remote control now can transmit B code control signals.
B
Check remote control code for recorder
Press and hold PLAY (4) on the recorder for more than 5 seconds
while the recorder is turned off. The code currently set appears on
the display panel.
C
Change code for recorder
Press any key on the remote control. The recorder now responds
to B code control signals.
To set the remote control and the recorder back to A code
control signals, repeat the same procedure as shown above
except pressing the Number key 1 in step B of 1.
To control two recorders with the same remote
control
You can control two JVC recorders by switching the remote
control code for the remote control between A and B (
step A),
keeping two recorders to different control codes.
To change only the remote control code for the remote control,
DO NOT perform steps B and C.
Editing
You can use your recorder as the playback or recording deck. You
can use a camcorder as the source player and your recorder as the
recording deck. Refer also to the other components instruction
manuals for connection and its operations.
A
Make connections
Example: When using this recorder as the source player
When using this recorder as the recording deck, connect this
recorders AV input connectors to the AV output connectors on
the other recorder. If the source player is monaural, connect the
audio output connector on the source player to the left audio
input connector on this recorder.
B
Load cassettes
Insert the playback cassette into the source player and the cassette
to be recorded on into the recording deck.
C
Select input mode on recording deck
Select the correct external input on the recording deck.
On this recorder (when using this recorder as the recording deck);
Select L-1 when connecting the other recorder to the AV
input connectors on the rear panel.
On the remote control
Press AUX or PR+/.
On the recorder
Press PAUSE[PR], and then FF[PR+] or REW[PR]. See step B in
Basic Recording.
D
Select edit mode
Set the edit mode to ON for the recorders if such a mode is
equipped.
On this recorder, set PICTURE CONTROL to EDIT.
E
Start playback
Press PLAY (
4
) on the source player.
F
Start recording
Press REC (
7
) on the recording deck.
To AV input
This recorder (for playback)
Another recorder (for recording)
AV cable
(not supplied)
To AUDIO/VIDEO OUT
Other Functions
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC HR-J281MS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC HR-J281MS in the language / languages: English as an attachment in your email.

The manual is 0,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info