118030
25
Zoom out
Zoom in
Previous page
1/52
Next page
Filename [HRJ480EU2.fm]
Masterpage:Right
EN
25
F
Enter the channel position.
G
Set the tape speed. (HR-J480EU only)
Press
SP/LP
(
p
).
H
Set the VPS/PDC mode.
Press
VPS/PDC
to select “ON” or “OFF”.
If “VPS/PDC ON” is displayed on the TV screen, VPS/PDC is
set to ON.
If “VPS/PDC OFF” is displayed on the TV screen, VPS/PDC is
set to OFF.
“VPS/PDC Recording” in the right column
I
Return to the normal screen.
After confirming all information is correct, press
PROG
or
OK
. “PROGRAM COMPLETED” appears on the TV
screen for about 5 seconds, then the normal screen
appears. If “PROGRAM OVERLAPPED” appears on the
TV screen, see page 27.
Repeat steps
1
9
for each additional programme.
J
Engage the recorder’s timer mode.
Press
#
(
TIMER
). The recorder turns off automatically and
#
appears on the front display panel.
To disengage the timer mode, press #
(
TIMER
) again.
To Timer-Record Weekly Or Daily Serials . . .
. . . anytime during steps
2
through
8
, press
WEEKLY
(
NUMBER
key “
9
”) for weekly serials or
DAILY
(
NUMBER
key “
8
”) for daily
serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears
on the TV screen. Pressing the button again makes the
corresponding indication disappear.
NOTE:
You can programme this recorder to timer-record as many as
8 programmes. If you try to programme the recorder to record a
ninth, “PROGRAM FULL” appears on the TV screen. To record
the extra programme, you must first cancel any unnecessary
programmes (
pg. 26).
Press
PR
+/–
.
VPS/PDC Recording
Now available from some TV stations, PDC (Programme
Delivery Control) and VPS (Video Programme System) are
service designed to assure safe, accurate timer recording.
With this system, special code signals are transmitted
together with the audio/video signals. These code signals
control your video recorder and have precedence over the
advertised times you may have preset into the timer. This
means that your recorder will start and stop recording when
the preset TV programmes actually start and end — even if
the broadcast time of a preset TV programme is changed.
NOTES:
When you use Express Timer Programming, set the start
time (VPS or PDC time) exactly as advertised in the TV
listing. A different time than advertised will result in no
recording.
VPS/PDC recording is also possible when a satellite
receiver or a cable system is connected to AV2 (L-2) IN/
DECODER on your recorder.
VPS/PDC recording is also possible via the AV1 (L-1) IN/
OUT connector.
How to check if the station being received transmits a
VPS/PDC signal
A Press
– –:– –
until the channel position appears on the
front display panel.
B Hold down
START+
for about 5 seconds.
“VPS/PDC” appears blinking on the TV screen.
If a VPS/PDC signal is detected from the station, “VPS/
PDC” will stop blinking.
If no VPS/PDC signal is detected from the station, “VPS/
PDC” will blink at a slower rate.
C Press
– –:– –
or
START+
again to return to normal display.
HRJ480EU2.fm Page 25 Friday, January 12, 2001 4:58 PM
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC HR-J280 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC HR-J280 in the language / languages: English as an attachment in your email.

The manual is 2,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info