136223
62
Zoom out
Zoom in
Previous page
1/80
Next page
Masterpage:Left-FullCol
62
EN
Filename [HRJ880EU4.fm]
Page 62 May 18, 2001 2:45 pm
SUBSIDIARY SETTINGS (cont.)
* The default setting is
bold
in the table below.
8
AUTO SP
]
LP TIMER
ON
OFF
When this function is set to “ON”, the recorder automatically switches to LP
mode to allow complete recording if there is not enough tape to record the
entire programme while timer-recording in SP mode.
For Example . . .
Recording a programme of 210 minutes in length onto a 180-minute tape
Make sure you set this function to “ON”, before the timer-recording starts.
NOTES:
If you have programmed the recorder to timer-record 2 or more programmes, the
second programme and those thereafter may not fit on the tape if you set “AUTO
SP
]
LP TIMER” to “ON”. In this case, make sure the mode is not engaged, then set
the tape speed manually during timer programming.
In order to ensure that the recording fits on the tape, this feature may leave a slight
non-recorded section at the end of the tape.
There may be some noise and sound disturbance at the point on the tape where the
recorder switches from SP to LP mode.
The Auto SP
]
LP Timer feature is not available during ITR (Instant Timer Recording),
and the feature will not work properly with any tapes longer than E-180, or with
some tapes of shorter lengths.
If you perform timer recording with both VPS/PDC and the Auto SP
]
LP Timer
activated, and the programme goes beyond its originally scheduled length, there
may be times when the programme cannot be recorded in its entirety.
8
POWER SAVE
ON
OFF
When this function is set to “ON”, you can reduce the power consumption
while the recorder is turned off.
NOTES:
During Power Save mode ...
... the front display panel will be turned off.
... the Just Clock function (
pg. 72) does not work.
... the picture may be distorted momentarily when you turn on/off the recorder.
Power Save does not work when ...
... the recorder is in the Timer mode.
... the recorder’s power is turned off after timer-recording or Instant Timer Recording.
... the Automatic Satellite Programme Recording mode is engaged (
pg. 34).
... “L-2 SELECT” is set to “DECODER” or “SAT” (
pg. 63).
8
VIDEO STABILIZER
ON
OFF
When this function is set to “ON”, you can automatically correct vertical
vibration in the picture when playing back unstable recordings made on
another recorder.
NOTES:
When you finish viewing a tape, be sure to set this function to “OFF”.
Regardless of the setting, this function has no effect during recording and during
special effects playback.
The on-screen display may jitter vertically when this function is set to “ON”.
To watch recordings with close-caption, set this function to “OFF”.
Total 210 minutes
Approximately 150 minutes Approximately 60 minutes
SP mode LP mode
HRJ880EU4.fm Page 62 Friday, May 18, 2001 2:56 PM
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC hr j 880 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC hr j 880 in the language / languages: English as an attachment in your email.

The manual is 5,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info