40749

JVC HR-A437E Manual

31
Zoom out
Zoom in
Previous page
1/33
Next page
4
INSTALLING YOUR NEW RECORDER (cont'd)
SET TV CHANNEL
3
Set your TV to the video channel (UHF channel 36).
Two white bars appear on screen vertically.
● Tune the TV until the bars are as clear as they can be.
● Your TV should be set to the channel designated for
use with a video recorder, or to a spare channel if
there is not a specified video channel on your TV.
RESET OUTPUT MODE
4
Return the RF TEST switch to OFF.
NOTES:
●
If CH36 is occupied by a local station, adjust the RF output
channel adjustment screw to use another channel between
CH32 and CH40 instead.
●
If some interference noise is continually seen on the screen,
consult your JVC dealer.
SELECT INPUT MODE
1
Set the AV2 SELECT switch to "DECODER".
CONNECT DECODER
2
Connect your recorder's AV2 IN/DECODER connector
to the decoder's Euroconnector using a 21-pin SCART
cable.
SET TUNER
3
Follow the procedure starting on page 6.
The AV2 IN/DECODER connector can be used as an input
terminal for an external decoder (descrambler). Simply connect
a decoder and you can enjoy the variety of programming that is
available through scrambled channels.
Connecting/
Using A
Decoder
(A233E, A433E
only)
TV Receiver
AV2 IN/DECODER
AV1 IN/OUT
AV2 SELECT switch
Decoder
Back of Recorder
RF Cable
(provided)
TV Aerial
Cable
5
The AV2 IN (/DECODER) or AV1 IN/OUT connector can be
used as an input terminal for a satellite tuner. Simply connect a
satellite tuner and you can enjoy the wide variety of satellite
programming.
Connecting/
Using A
Satellite Tuner
SELECT INPUT MODE
(A233E, A433E only)
1
Set the AV2 SELECT switch to “AV2”.
CONNECT SATELLITE
TUNER
2
●
If you own the A230E, A430E or A437E . . .
. . . connect an optional 21-pin SCART cable between
the satellite tuner's Euroconnector and your
recorder's AV1 IN/OUT connector.
●
If you own the A233E , A237E or A433E . . .
. . . connect an optional 21-pin SCART cable between
the satellite tuner's Euroconnector and your
recorder's AV2 IN (/DECODER) connector.
PREPARE TO WATCH A
SATELLITE PROGRAMME
3
Select the appropriate channel on the satellite tuner.
Then set the auxiliary mode as follows:
●
If you own the A230E, A430E or A437E . . .
. . . press NUMBER key "0" or TV PROG. on the remote
control until "AU" appears on the recorder's front
display panel.
●
If you own the A233E, A237E or A433E . . .
. . . press NUMBER key "0" or TV PROG. on the remote
control until "AU2" appears on the recorder's front
display panel.
NOTE:
When connecting a satellite tuner together with a decoder . . .
. . . first connect the satellite tuner's output connector to the
decoder's input connector, then connect the decoder's
output connector to the recorder's AV2 IN or AV1 IN/OUT
connector (depending on the model of recorder you own).
TV Receiver
RF Cable
(provided)
TV Aerial
Cable
Decoder
AV1 IN/OUT
Back of Recorder
Satellite antenna
Satellite tuner
AV2 SELECT switch
AV2 IN (/DECODER)
6
INITIAL SETTINGS
ACCESS CONFIRMATION
DISPLAY
6
The channel position, channel and station name
[A237E, A437E only] of the stations located by your
recorder appear in a Confirmation display (੬ pg. 24).
Confirm all the stored stations by using PUSH JOG
%
fi
.
●
If you own the A230E, A233E, A430E or A433E . . .
. . . you can manually input the station name
(੬ pg. 23).
RETURN TO NORMAL
DISPLAY
7
Press CH SET.
● Using the Confirmation display, you can skip or add channel
positions, enter station names and perform other operations.
Refer to page 22 for the procedures.
● Depending on the reception conditions, the stations may not
be stored in order, and (for A237E or A437E only) the station
names may not be stored correctly.
● If you own the A233E or A433E and use a decoder, ੬ pg. 22
for information on scrambled broadcasts.
NOTES:
●
Fine tuning is performed automatically when you select
"AUTO" in step 2. If you want to perform it manually, refer to
page 23.
●
To set the tuner manually, refer to "Storing Channels Manu-
ally" (
੬
pg. 22).
Tuner Set
Your recorder needs to memorise all necessary stations in
channel positions in order to record TV programmes. The Auto
Tuning System automatically assigns all receivable stations in
your area to call them up with the TV PROG. buttons without
going through any vacant channels.
The following procedure describes how to select automatic
channel setting.
TURN ON THE RECORDER
1
Press OPERATE.
ACCESS CH. SET DISPLAY
2
Press and hold CH SET for more than 2 seconds.
“AUTO” appears on the front display panel.
●
If you own the A237E or A437E . . .
. . . go directly to step 3.
●
If you own the A230E, A233E, A430E or A433E . . .
. . . skip to step 5.
ACCESS COUNTRY DIS-
PLAY
3
Press OK and the Country display appears on the front
display panel.
SELECT COUNTRY
4
Press PUSH JOG %fi to select your country’s name.
The available country names appear in the following
order:
•
If you own the A237E or A437E and you selected
"BELG" or "SUIS" above . . .
. . . refer to "INFORMATION" at the end of this page.
START AUTO CHANNEL
SET
5
Press OK and “AUTO" blinks on the front display panel.
●
If you own the A237E or A437E and you selected
"BELG" or "SUIS" in step 4 . . .
. . . refer to "INFORMATION" at the end of this page.
(for HR-A237E, A437E)
(for HR-A230E, A233E, A430E, A433E)
Channel Position
≠
Channel
≠
Station Name
≠
"AUT" (Österreich) "OTHR" (Others)
"BELG" (Belgium) "SWED" (Sverige)
"DEUT" (Deutschland) "SUOM" (Suomi)
"DK" (Danmark) "SUIS" (Suisse)
"ESP" (España) "PORT" (Portugal)
"GRCE" (Greece) "NOR" (Norsk)
"ITA" (Italia) "NL" (Nederland)
Ch=Regular CC=Cable
INFORMATION
If you own the A237E or the A437E and you selected “BELG” or
“SUIS” in step 4, you need to enter the language used in your area.
This ensures that stations broadcasting programmes in your language
will be stored in the highest channel positions. Once you select a
language, the recorder selects the region.
After pressing OK in step 5, perform the following procedure:
1. Press PUSH JOG%fi to select your language.
• Users living in Belgium should select "DEUT", "FRA"
or "NL".
• Users living in Suisse should select "DEUT", "FRA" or "ITAL".
The available languages appear in the following order:
2. Press OK, then go to step 6.
"ENG" (English) "DK" (Dansk)
"DEUT" (Deutsch) "SUOM" (Suomi)
"FRA" (Français) "NOR" (Norsk)
"ITAL" (Italiano) "SWED" (Svenska)
"CAST" (Castellano) "NL" (Nederlands)
7
Clock Set
The following procedures are for the A230E, A233E, A430E
and A433E.
TURN THE RECORDER ON
1
Press OPERATE.
ACCESS CLOCK SET
DISPLAY
2
Press CLOCK on the remote control. The Clock Set
display appears.
SET DATE AND TIME
3
Press PUSH JOG %fi to set the hour, then press OK.
The “minutes” display begins blinking. Repeat the
procedure to set the minutes, day, month and year.
START CLOCK OPERATION
4
Press CLOCK.
NOTES:
●
During clock setting, if the day and month data are invalid
(such as 31st April), the month digits are cleared automati-
cally and the day digits begin blinking. Input the correct data.
●
If, in step 3, the year digits are automatically cleared and the
day digits begin blinking, it is possible that you have input
29th February for a non-leap year. Input the correct data.
The following procedures are for the A237E and the A437E.
If you performed Auto Channel Set (੬ pg. 6), the recorder’s
built-in clock is also set automatically. The Auto and Manual
clock setting procedures are necessary when . . .
– a power outage of more than 3 minutes occurs.
– the tuner has been set manually.
– the user desires to set the clock slightly ahead of the actual
time.
– the clock was not set even after Auto Tuner Set was
performed.
Whether you perform Auto or Manual clock setting, you can
use the convenient Just Clock function.
Just Clock
The Just Clock function provides accurate time keeping through
automatic adjustments at regular intervals, by reading data from
a PDC signal.
The Just Clock option appears in the Just Clock display, and can
be set “ON” or “OFF” (the default setting is “ON”). Press OK
until the Just Clock setting begins blinking, then press PUSH
JOG%fi to change the setting.
IMPORTANT: If you turn off Just Clock off, the accuracy of your
recorder’s built-in clock may be reduced, which could
adversely effect timer recording.
Both Auto and Manual clock setting procedures begin from step
3.
Just Clock Channel Position
≠
TURN THE RECORDER ON
1
Press OPERATE.
ACCESS CLOCK SET
DISPLAY
2
Press CLOCK on the remote control. The Clock Set
display appears.
Preparation
CONTINUED ON NEXT PAGE.
M
D
Minutes
≠
Hour
≠
Year
≠
Month
≠
Day
≠
8
INITIAL SETTINGS (cont.)
SET CLOCK
AUTOMATICALLY
3
At the Clock Set display, press PUSH JOG . The Clock
Set display blinks and clock setting begins.
● If the Just Clock channel position isn't set to the
channel position on which Auto Clock data is
received, "Err"(or) appears, and then the display from
step 2 reappears. To set the Just Clock channel
position, press OK until the Just Clock channel
position begins blinking, then cycle through the
numbers by pressing PUSH JOG%fi until the number
representing the channel position in which the station
transmitting clock setting data is stored appears.
RETURN TO NORMAL
DISPLAY
4
Once clock setting is completed, press CLOCK to return
to the normal display.
Auto Clock Set
SET DATE AND TIME
3
Press PUSH JOG%fi to set the hour, then press OK. The
“minutes” display begins blinking. Repeat the proce-
dure to set the minutes, day, month and year.
After inputting the year, press OK and the Just Clock
display appears.
SET JUST CLOCK
4
The default setting is “ON”. Set as desired by pressing
PUSH JOG%fi, then press OK.
● If you set to “OFF”, you can disregard the next step as
you won’t be able to receive regular clock adjust-
ments.
Manual Clock Set
SET CLOCK DATA SOURCE
CHANNEL POSITION
5
The recorder is preset to receive clock setting and
adjustment data from channel position 1. Press PUSH
JOG%fi to set the channel position to the number
representing the station transmitting clock setting data,
then press OK.
START CLOCK OPERATION
6
Press CLOCK.
NOTES:
●
Auto Clock and Just Clock require a PDC signal, and will not
operate with a VPS signal.
●
Just Clock (when set to "ON") enables adjustment of the
recorder's built-in clock every hour on the hour, except for 11
o'clock in the evening and midnight.
●
Just Clock is not effective when . . .
– the recorder’s power is on (unless the recorder is tuned to
the same channel position selected in the Just Clock
display).
– the recorder is in the Timer mode.
– a difference of more than 3 minutes exists between the
built-in clock’s time and the actual time.
●
If Just Clock is set to "ON", the recorder’s clock is automati-
cally adjusted at the start/end of Summer Time.
●
Auto clock setting and Just Clock may not function properly
depending on the reception condition.
●
During Manual clock setting, if the day and month data are
invalid (such as 31st April), the month digits are cleared
automatically and the day digits begin blinking. Input the
correct data.
●
If, in step 3 of the Manual Clock Set procedure, the year digits
are automatically cleared and the day digits begin blinking, it
is possible that you have input 29th February for a non-leap
year. Input the correct data.
%
M
D
Year
≠
Day
≠
Month
≠
Hour
≠
Minutes
≠
31
DISPLAY PANEL
1 and 2 Symbolic Mode Indicators 3 Start Time/Stop Time Indicator (੬ pg. 18)
4 PDC/VPS Indicator (੬ pg. 17)
[A237E, A437E only]
5 ”DAILY” Program Mark (੬ pg. 18)
6 ”WEEKLY” Program Mark (੬ pg. 18)
7 ”Cassette Loaded” Mark
8 Instant Timer Recording (੬ pg. 14)
9 Tape Speed Indicators (੬ pg. 13) [A430E,
A433E, A437E only]
0 ”Timer” Indicator (੬ pg. 18)
! Clock/Counter Display (੬ pg. 7)
@ Channel/Mode Display (੬ pg. 6)
# VIDEO indicator (੬ pg. 10)
[A233E, A433E only]
PLAY: REVERSE PLAY:
FF:
STILL:
FORWARD SLOW:
REW:
STILL:
REVERSE SLOW:
FF VARIABLE
RECORD:
SHUTTLE SEARCH:
REW VARIABLE
RECORD PAUSE:
SHUTTLE SEARCH:
SP
LP
EP
M
D
D
I T R
W
VIDEO
708 ! @
1
2
3
4
5
6
9 #
… 31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC HR-A437E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC HR-A437E in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info