595810
26
Zoom out
Zoom in
Previous page
1/49
Next page
48
6. SETTING AND ADJUSTMENTS BEFORE SHOOTING
Tw o kinds of white balance adjustment results can be stored in
memories AUTO1 and AUTO2.
Adjustment procedure
1.
Set the following switches.
Set the POWER switch to ON.
Set the OUTPUT switch to CAM-AUTO KNEE.
Set the IRIS mode switch of the lens to A (Auto).
2.
Set the FILTER knob according to the current lighting.
3.
Set the WHT.BAL switch to A or B.
4.
Place a white object near the centre of the screen under
the same lighting conditions as the target subject and zoom
in to fill the screen with white.
5.
Tilt the AUTO WHT./ACCU FOCUS switch upward (to AUTO
WHITE) once and release it.
“AUTO WHITE A, B OPERATION” is displayed in the
viewfinder while the auto white balance adjustment circuit
operates.
When correct white balance is obtained, the approximate
color temperature is displayed together with “AUTO WHITE
A, B OK” for about 5 seconds.
Error messages
If the adjustment ends abnormally, an error message, as
described below, blinks for about 5 seconds.
NG: OBJECT (Improper object)
Displayed when there is not enough white color on an object
or the color temperature is not suitable.
Replace the color temperature conversion filter or use another
white object and re-adjust the white balance.
ERROR: LOW LIGHT (Insufficient illumination)
Displayed when the illumination is dim. Increase the
illumination and then re-adjust the white balance.
ERROR: OVER LIGHT (Excessive illumination)
Displayed when the light is excessively bright. Decrease the
illumination and then re-adjust the white balance.
FULL-TIME AUTO WHITE BALANCE (FAW)
The FAW function adjusts the white balance value
automatically as the lighting condition changes.
This mode is convenient when you have no time to adjust the
white balance or when the camera is moved frequently in and
out of places under different lighting conditions.
Setting procedure
The FAW function can be activated with the FAW item on the
CAMERA OPERATION menu screen. The FAW function can
be allocated to one of the white balance switching switches
A, B, or PRESET.
See “CAMERA OPERATION menu screen” on page 69.
6-6 White Balance Adjustment
Since the color of light (color temperature) varies depending on the light source, it is necessary to re-adjust the white balance when
the main light source illuminating the subject changes.
Note
When a subject illuminated by a halogen lamp with a color temperature of 3,200K is shot while the color temperature conversion
filter setting is set to 5,600K, 5,600K+1/8 ND, or 5,600K+1/64 ND, a proper white balance adjustment and (FAW) Full Time Auto
White balance may not be accomplishable. In this case, change the color temperature conversion filter setting to 3,200K and
then carry out the white balance adjustment and (FAW) again.
Do not adjust using any highly reflective objects, such as metal, etc., as this may result in improper white balance adjustment.
WHITE BALANCE ADJUSTMENT
1.
1.
1.
5.
3.
2.
Iris mode
switch
FILTER knob
AUTO WHT.
/ACCU FOCUS switch
WHT.BAL
switch
OUTPUT
switch
POWER
switch
AUTO WHITE A
OPERATION
AUTO WHITE A
OK
<3200K>
AUTO WHITE A
NG:OBJECT
AUTO WHITE A
ERROR:LOW LIGHT
AUTO WHITE A
ERROR:OVER LIGHT
During operation
Improper object
Result message
Insufficient illumination
Excessive illumination
CAUTION:
The FAW (Full-time Auto White balance) function cannot
provide optimum white balance with a subject outside
the FAW adjustment range, for example when it contains
only a single color or not enough white color.
The accuracy of the FAW (Full-time Auto White balance)
is inferior to that of the manual white balance.
When the power is turned on with the FAW mode
selected, it takes about 10 seconds for the FAW
adjustment to be completed. Do not shoot within this
interval.
49
6. SETTING AND ADJUSTMENTS BEFORE SHOOTING
MONITOR
EDITSEARCH
FILTER
STATUS
SHUTTER
MENU
AUTO IRIS
BACK L
NORMAL
SPOT L
STRETCH
NORMAL
COMPRESS
FULL AUTO BLACK LOLUX
MODE
POWER
ON OFF
VTR
OPEN
VTR
CAM
1
3200K
5600K
5600K
5600K
ND
/
/
ND
2
.3
.4
1
8
1
64
CH-1
AUDIO INPUT
AUDIO SELECT
CH-2
CH-1 CH-2
FRONT
REAR
AUTO
MANUAL
AUDIO
LEVEL
CH-1 CH-2
PULL
OPEN
LCD BRIGHT DISPLAY
COUNTER
CH-1
AUDIO INPUT
AUDIO SELECT
CH-2
CH-1 CH-2
FRONT
REAR
AUTO
MANUAL
TC GENE.
TC
MONITOR
SELECT
AUDIO
LEVEL
AUDIO INPUT
CH-1 CH-2
CH-1
MIX
CH-2
FRONT REAR
LINE
MIC
+48V
PRST
REGEN FREE
REC
UB
LCD BRIGHT DISPLAY
VF
ZEBRA
AUDIO
LEVELE CH-1
OFF
ON
SKIN
AREA
AUTO
WHITE
ACCU
FOCUS
VTR
5
PHONES
DC OUT
DC IN
DV REAR AUDIO IN TALLY
6-7 Audio Input Signal Selection
REAR AUDIO IN
connector
FRONT AUDIO IN
connector
AUDIO INPUT
(LINE/MIC) switch
CH-1 AUDIO INPUT switch
CH-2 AUDIO INPUT
switch
The GY-DV5000 is provided with the FRONT AUDIO IN
connector and the REAR AUDIO IN connector for audio input.
Tw o channels of sound can be recorded on the tape in digital
PCM format. Using the AUDIO INPUT switch, select for each
channel (CH1 and CH2) whether the sound to be recorded
should be the sound from the FRONT AUDIO IN connector or
the sound from the REAR AUDIO IN connector.
Selecting the CH-1 channel input sound
Make the selection using the CH-1 AUDIO INPUT switch.
FRONT : The sound from the FRONT AUDIO IN connector
is recorded on the CH-1 channel.
REAR : The sound from the REAR AUDIO IN connector is
recorded on the CH-1 channel.
Selecting the CH-2 channel input sound
Make the selection using the CH-2 AUDIO INPUT switch.
FRONT : The sound from the FRONT AUDIO IN connector
is recorded on the CH-2 channel.
REAR : The sound from the REAR AUDIO IN connector is
recorded on the CH-2 channel.
Selecting the FRONT AUDIO IN connector and REAR
AUDIO IN connector
Select the sound to be input to the AUDIO INPUT connector
using the AUDIO INPUT (LINE/MIC) switch. The setting is
made individually for both the FRONT AUDIO IN connector
and the REAR AUDIO IN connector.
LINE : Set to this position when connected to audio
equipment, etc.
The reference input level is +4 dBs.
MIC : Set to this position when using a monaural
microphone.
The reference input level is -60 dBs.
+48 V : Set to this position when a microphone
(phantom microphone) requiring +48 V DC
power supply is connected.
CAUTION:
Before connecting a component that does not require +48
V power supply, make sure that the AUDIO INPUT (LINE/
MIC) switch is not set to +48 V.
Neglecting this could cause damage to the connected
component.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC GY-DV5000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC GY-DV5000 in the language / languages: English as an attachment in your email.

The manual is 3,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info