34423
68
Zoom out
Zoom in
Previous page
1/96
Next page
68
12. SETUP MENU
Group
Item
Setting
Contents
Factory
Value
Setting
Upper row: Viewfinder display
Lower row: Counter display indication
VCR SETUP MENU CONTENTS
SERVO
/SYSTEM
VIDEO
AUDIO
050: REMOTE SELECT
rnSL
082: BACK TALLY MODE
rtMd
126: INPUT SELECT
vld
244: LOW CUT
LctF
245: SAMPLING RATE
snPL
246: FRONT VOLUME
ENABLE
FruL
LOCAL
IEEE1394
RS232C
Lc
IE
23
OFF
ON
BLINK
oF
on
bL
CAMERA
IEEE1394
cA
IEEE1394
OFF
CH1
CH2
CH1 &
CH2
oF
01
02
on
32K
48K
32
48
DISABLE
ENABLE
oF
on
Selection of the method for remote control of the VCR.
LOCAL : Choose this setting when the VCR should
be controlled using the operation buttons
on the GY-DV500 only.
IEEE1394 : Choose this setting when the VCR should
be remote controlled from a DV connector
equipped video component connected to
the DV connector on the rear section of the
GY-DV500.
RS232C : Choose this setting for control by means of
the VCR remote control signal from the VTR
REMOTE connector on the GY-DV500.
* The operation buttons on the GY-DV500 remain
effective even when set to IEEE1394 or RS232C.
Selection of the lighting pattern of the BACK TALLY lamp
on the rear section during recording.
OFF : The lamp is always off.
ON : The lamp lights during recording. It remains
off until the VTR trigger button is pressed
to start the recording.
BLINK : The lamp lights during recording. It blinks
when the VTR trigger button is pressed to
start the recording.
Selection of the input video signal.
Settings cannot be changed during recording.
CAMERA : Camera image is input.
IEEE1394 : The image from the DV connector equipped
video component connected to the DV
connector on the rear section is input.
To select whether or not the low frequencies of the audio
signal from the audio input connectors are cut. Set to
ON to reduce the wind noise of the microphone.
OFF :
The CH1 and CH2 low frequencies are not cut.
CH1 : Only the low frequencies of the audio signal
input to the CH1 channel are cut.
CH2 : Only the low frequencies of the audio signal
input to the CH2 channel are cut.
CH1& CH2
:The low frequencies are cut for both CH1
and CH2.
To select the sampling rate for digital PCM audio recording.
32K : Digital recording occurs with 12-bit, 32 kHz
sampling
48K : Digital recording occurs with 16-bit 48 kHz
sampling.
* The DV format offers recording tracks for up to 4
channel when recording using 12-bit, 32 kHz
sampling. The GY-DV500 records two of these tracks.
The GY-DV500 does not allow after-recording.
To select whether or not the front section recording level
control should be operative. The front section recording
level control only affects the audio signal recorded on CH1.
DISABLE : Use of the front section recording level
control is disabled.
ENABLE : Use of the front section recording level
control is enabled.
* The CH-1 recording level control on the side section
works regardless of the setting.
LOCAL
BLINK
CAMERA
OFF
48K
ENABLE
12-1 VCR Setup Menu (Cont'd)
68


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC GY-DV500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC GY-DV500 in the language / languages: English as an attachment in your email.

The manual is 4,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info