46754
49
Zoom out
Zoom in
Previous page
1/64
Next page
EN 49
EDITING
MasterPage: Start_Right
ADVANCED FEATURES
Never connect the USB cable and the DV
cable simultaneously to the camcorder.
Connect only the cable you wish to use to the
camcorder.
When using a DV cable, be sure to use the
optional JVC VC-VDV206U or VC-VDV204U DV
cable depending on the type of DV connector
(4 or 6 pins) on the PC.
If the PC connected to the camcorder via the USB
cable is not powered, the camcorder does not
enter the USB mode.
The date/time information cannot be captured into
the PC.
Refer to the instruction manuals of the PC and
Software.
The still images can also be transferred to a PC
with a DV connector-equipped capture board.
The system may not work properly depending on
the PC or capture board you are using.
You can record a new scene into a previously
recorded tape, replacing a section of the original
recording with minimal picture distortion at the in
and outpoints. The original audio remains
unchanged.
Use the provided remote control.
NOTES:
Before performing the following steps, make sure
that “TIME CODE” is set to “ON” in CAMERA
DISPLAY and VIDEO DISPLAY menus.
( pg. 33, 36, 38)
Insert editing is not possible on a tape recorded in
the LP mode or on a blank portion of a tape.
1 Play back the
tape, locate the edit-
out point and press
PAUSE (9). Confirm
the time code at this
point. ( pg. 19)
2 Press REW (
3
)
until the edit-in point is located, then press
PAUSE (9).
3 Press and hold INSERT (I) on the remote
control, then press PAUSE (9). The “9I
indicator and the time code (min.:sec.) appear
and the camcorder enters insert-pause mode.
4 Press START/STOP to begin editing.
Confirm the insert at the time code you checked in
step 1.
To pause editing, press START/STOP. Press it
again to resume editing.
5 To end insert editing, press START/STOP,
then STOP (8).
NOTES:
Program AE and special effects ( pg. 44, 45)
can be used to spice up the scenes being edited
during insert editing.
During insert editing, the date and time
information changes.
If you perform insert editing onto a blank space on
the tape, the audio and video may be disrupted.
Make sure you only edit recorded areas.
During insert editing, when the tape moves to
scenes recorded in the LP mode or a blank
portion, insert editing stops. ( pg. 55)
Insert Editing
PAUSE
STOP
REW
INSERT
START/
STOP
GR-XASIA.book Page 49 Tuesday, April 12, 2005 8:52 PM
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC GR-X5AG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC GR-X5AG in the language / languages: English as an attachment in your email.

The manual is 5,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info