Manual JVC GR-DX75 (page 43 of 60) (English)

39852

Zoom out

Zoom in

1/60

USING THE REMOTE CONTROL UNIT

For More Accurate Editing

Some VCRs make the transition from Record-Pause to

Record mode faster than others. Even if you begin

editing for the camcorder and the VCR at exactly the

same time, you may lose scenes you wanted, or find

that you have recorded scenes you did not want. For a

cleanly edited tape, confirm and adjust the timing of the

camcorder against your VCR.

DIAGNOSING VCR/CAMCORDER TIMING

1 Play back the tape in the camcorder, then point the

remote control at the camcorder’s remote sensor and

press R.A.EDIT ON/OFF J.

The Random Assemble Editing Menu appears.

2 Perform Random Assemble Editing on Programme 1

only. In order to check VCR and camcorder timing,

select the beginning of a scene transition as your Edit-

In point.

3 Play back the dubbed scene.

• If any images from the scene prior to the transition

you chose for your Edit-In point were recorded, that

means your VCR moves too quickly from Record-

Pause to Record mode.

• If the scene you tried to dub starts in progress, the

VCR is slow to start recording.

ADJUSTMENT OF VCR/CAMCORDER TIMING

4 Point the remote control at the camcorder’s remote

sensor and press R.A.EDIT ON/OFF J to make the

Random Assemble Editing menu disappear, then press

MENU 4. The Menu Screen appears.

5 Press + or – 5 to select “ (VIDEO)” and press

SELECT/SET 3. Then, press + or – 5 to select

“SYNCHRO” and press SELECT/SET 3. The value for

“SYNCHRO” is highlighted.

6 Based on the diagnostics performed, you can now

advance the VCR’s record timing by pressing + 5. You

can also delay the VCR’s record timing by pressing –

5. The adjustment range is from –1.3 to +1.3 seconds,

in 0.1-second increments. Press SELECT/SET 3 to

finish the setting.

7 Press + or – 5 to to select “ RETURN” and press

SELECT/SET 3 twice.

Now perform Random Assemble Editing beginning with

step 4 on page 42.

NOTES:

● Before performing actual Random Assemble Editing, do a

few Random Assemble Editing trial runs to check whether

the value you have input is appropriate or not, and make

adjustments accordingly.

● Depending on the recorder, there may be situations

where the timing difference cannot be fully corrected.

Picture Wipe/Dissolve (GR-DX300/DX100 only)

(available only for Random Assemble Editing)

You can also use the fade/wipe effects on page 28.

DISSOLVE

The new scene gradually appears as the old one gradually

disappears.

WIPE — CORNER

The new scene wipes in over the previous one from the

upper right corner to the lower left corner.

WIPE — WINDOW

The next scene gradually wipes in from the centre of the

screen toward the corners, covering the previous scene.

WIPE — SLIDE

The next scene gradually wipes in over the previous one

from right to left.

WIPE — DOOR

The previous scene wipes out from the centre to the right

and left, like a door being pushed open to reveal the next

scene.

WIPE — SCROLL

The new scene wipes in over the last one from the bottom

of the screen to the top.

WIPE — SHUTTER

The new scene wipes in over the previous one from the

centre toward the top and bottom of the screen.

AUTOMATIC EDITING TO VCR

Rewind the tape in the camcorder to the beginning

of the scene you want to edit and press PAUSE (6) H.

Point the remote control towards the VCR’s remote

sensor and press VCR REC STBY (q6) K, or

manually engage the VCR’s Record-Pause mode.

Press START/STOP k on the remote control.

Editing proceeds as programmed, right through to the

end of the last registered scene.

• When dubbing is complete, the camcorder enters the

Pause mode, and the VCR enters its Record-Pause

mode.

• If you do not register an Edit-Out point, the tape will

be dubbed all the way to the end automatically.

• If you operate the camcorder during automatic editing,

the VCR will enter its Record-Pause mode and

automatic editing will stop.

Engage the Stop modes for the camcorder and the

VCR.

To make the R.A.Edit counter display disappear, press

R.A.EDIT ON/OFF J on the remote control.

NOTES:

● Pressing R.A.EDIT ON/OFF J on the remote control

clears all settings registered during Random Assemble

Editing.

● When the editing cable is connected to the remote

control’s Pause In connector during dubbing, make sure

the remote control is pointed at the VCR’s sensor, and

the path between the two is unobstructed.

● Random Assemble Editing may not function properly

when using a tape including several duplicated time

codes (

੬ pg. 14).

01 DX300/100/95/75EK_EN 35-44 2/26/03, 7:13 PM43

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of JVC GR-DX75 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JVC GR-DX75

JVC GR-DX75 User Manual - German - 60 pages

JVC GR-DX75 User Manual - Dutch - 60 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

JVC GR-DX75 Manual

Product: