39838
40
Zoom out
Zoom in
Previous page
1/52
Next page
EDITING
40 EN
MasterPage: Left
The audio track can be customised only when recorded
in the 12-BIT and SP modes. ( pg. 28)
Use the provided remote control or an optional remote
control kit RM-V717KITU.
1 Play back the tape to locate the point where editing
will start, then press PAU SE (9).
2 While holding A. DUB (D) on the remote control,
press PAU SE (9). The 9D and MIC indicators
appear.
3 Press PLAY (U), then begin narrating. Speak into
the microphone.
To pause dubbing, press PAUSE (9).
4 To end Audio Dubbing, press PAU SE (9), then STOP
(8).
To hear the dubbed sound during playback
Set NARRATION to ON or MIX. ( pg. 27, 30)
NOTES:
Sound is not heard from the speaker during Audio Dubbing.
When editing onto a tape that was recorded at 12-BIT, the
old and new soundtracks are recorded separately.
If you dub onto a blank space on the tape, the sound may
be disrupted. Make sure you only edit recorded areas.
If feedback or howling occurs during TV playback, move the
camcorders microphone away from the TV, or turn down
the TVs volume.
If you change from 12-BIT to 16-BIT in mid-recording and
then use the tape for Audio Dubbing, it is not effective from
the point where 16-BIT recording began.
During Audio Dubbing, when the tape moves to scenes
recorded in the LP mode, scenes recorded in 16-BIT audio
or a blank portion, Audio Dubbing stops.
Audio dubbing is also possible using an optional
microphone connected to the MIC connector.
While an optional microphone is connected, the built-in
microphone is disabled.
To perform Audio Dubbing with a video unit connected to
the camcorders AV connector, first set S/AV INPUT to A/
V. IN or S.IN in VIDEO Menu. (GR-DX97/77/57/37 only)
( pg. 27, 30)
The AUX indication appears instead of MIC.
You can record a new scene into a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in and outpoints. The
original audio remains unchanged.
Use the provided remote control or an optional remote
control kit RM-V717KITU.
NOTES:
Before performing the following steps, make sure that
TIME CODE is set to ON. ( pg. 27, 31)
Insert Editing is not possible on a tape recorded in the LP
mode or on a blank portion of a tape.
1 Play back the tape, locate the Edit-Out point and
press PAUSE (9). Confirm the time code at this point.
( pg. 17)
2 Press REW (
3
) until the Edit-In point is located,
then press PAUSE (9).
3 Press and hold INSERT (I) on the remote control,
then press PAUSE (9). The 9I indicator and the Time
Code (min.:sec.) appear and the camcorder enters
Insert-Pause mode.
4 Press START/STOP to begin editing.
Confirm the insert at the time code you checked in step 1.
To pause editing, press START/STOP. Press it again to
resume editing.
5 To end Insert Editing, press START/STOP, then
STOP (8).
NOTES:
Program AE with special effects ( pg. 35) can be used to
spice up the scenes being edited during Insert Editing.
During Insert Editing, the date and time information
changes.
If you perform Insert Editing onto a blank space on the
tape, the audio and video may be disrupted. Make sure you
only edit recorded areas.
During Insert Editing, when the tape moves to scenes
recorded in the LP mode or a blank portion, Insert Editing
stops. ( pg. 47)
Audio Dubbing
PAUSE
PLAY
A.DUB
STOP
REW
INSERT
START/
STOP
Microphone Connector
Speaker
Stereo Microphone
Insert Editing
GR-DX97PAL.book Page 40 Tuesday, January 6, 2004 12:44 PM
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC GR-DX48 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC GR-DX48 in the language / languages: English as an attachment in your email.

The manual is 3,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JVC GR-DX48

JVC GR-DX48 User Manual - German - 52 pages

JVC GR-DX48 User Manual - Dutch - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info