595798
16
Zoom out
Zoom in
Previous page
1/92
Next page
16 EN
25
min
90 min
89 min
3 min
2 min
1 min0 min
min
180°
90°
BR I GHT
VIDEO RECORDING
Power lamp
Tally lamp (lights while
recording is in progress)
Lock Button
Recording Start/Stop Button
Tape remaining
time indicator
(Approximate)
(Now calculating)
(Blinking) (Blinking) (Blinking)
Display
MENU/BRIGHT Wheel
Power Switch
PUSH-OPEN
Button
Basic Recording
NOTE:
You should already have performed the procedures listed
below. If not, do so before continuing.
Power (
pg. 8)
Grip Adjustment (
pg. 10)
Viewfinder Adjustment (
pg. 10)
Load A Cassette (
pg. 12)
Recording Mode Setting (
pg. 13)
1
Press in the tabs on the lens cap to remove it.
GR-DVL817 only:
Press PUSH OPEN, open the LCD
monitor and set the VIDEO/DSC Switch to VIDEO.
2
Set the Power Switch to or while pressing
down the Lock Button located on the switch.
Shooting while using the LCD monitor:
Make sure
the LCD monitor is fully open. Tilt it upward/
downward for best viewability.
Shooting while using the viewfinder:
Close the LCD
monitor.
The power lamp lights and the camcorder enters the
Record-Standby mode. PAUSE is displayed.
3
Press the Recording Start/Stop Button.
appears while recording is in progress.
To Stop Recording . . .
.... press the Recording Start/Stop Button. The camcorder
re-enters the Record-Standby mode.
To Adjust The Brightness Of The Display
.... rotate the MENU/BRIGHT wheel until the bright level
indicator on the display moves and the appropriate
brightness is reached.
If you are using the GR-DVL515, it is also possible to
adjust the brightness of the viewfinder by closing the
LCD monitor and adjusting as described above.
NOTES:
If the Record-Standby mode continues for 5 minutes, the
camcorders power shuts off automatically. To turn the
camcorder on again, set the Power Switch to OFF,
then back to or .
The image will not appear simultaneously on the LCD
monitor and the viewfinder. It will appear in the
viewfinder when the LCD monitor is in the lock
position, and it will appear on the LCD monitor when
fully extended.
When a blank portion is left between recorded scenes
on the tape, the time code is interrupted and errors may
occur when editing the tape. To avoid this, refer to
Recording from the middle of a tape (
pg. 20).
To turn the tally lamp or beep sounds off,
pg. 46, 48.
VIDEO/DSC Switch
(GR-DVL817 only)
During
shooting
For other notes, pg. 71
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC GR-DVL515 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC GR-DVL515 in the language / languages: English as an attachment in your email.

The manual is 2,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info