23029
14
Zoom out
Zoom in
Previous page
1/56
Next page
EN
14
TAPE RECORDING
Time Code
During recording, a time code is recorded on the tape.
This code is to confirm the location of the recorded
scene on the tape during playback.
If recording starts from a blank portion, the time code
begins counting from 00:00:00 (minute:second:frame).
If recording starts from the end of a previously recorded
scene, the time code continues from the last time code
number.
If during recording a blank portion is left partway
through the tape, the time code is interrupted. When
recording is resumed, the time code starts counting up
again from 00:00:00. This means the camcorder may
record the same time codes as those existing in a
previously recorded scene. To prevent this, perform
RECORDING FROM THE MIDDLE OF A TAPE in the
following cases;
When shooting again after playing back a recorded
tape.
When power shuts off during shooting.
When a tape is removed and re-inserted during
shooting.
When shooting using a partially recorded tape.
When shooting on a blank portion located partway
through the tape.
When shooting again after shooting a scene then
opening/closing the cassette holder cover.
Display
RECORDING FROM THE MIDDLE OF A TAPE
1 Play back a tape or use Blank Search ( pg. 15) to
find the spot at which you want to start recording, then
engage the Still Playback mode ( pg. 14, Normal
Playback).
2 Set the Power Switch y to or while
pressing down the Lock Button t located on the
switch, then start recording.
NOTES:
The time code cannot be reset.
During fast-forwarding and rewinding, the time code
indication does not move smoothly.
The time code is displayed only when TIME CODE is
set to ON (
pg. 31).
Frames
(30 frames = 1 second)
Seconds
Minutes
Frames are not displayed
during recording.
Normal Playback
1 Load a tape ( pg. 9).
2 Set the VIDEO/DSC Switch 4 to VIDEO (GR-D90/
D70 only), then set the Power Switch y to PLAY
while pressing down the Lock Button t located on the
switch. To start playback, press
4
/6 7.
To stop playback temporarily (Still Playback), press
4
/6 7.
To stop playback, press 5 5.
Press
2
6 to rewind, or
3
8 to fast-forward the
tape during Stop mode.
High-speed picture search (Shuttle Search) is
possible by pressing
2
6 or
3
8 during playback
(holding
2
6 or
3
8 down during playback
continues search until released).
Press the Zoom Button T ; on the remote control to
zoom in (up to 44X), or W A to zoom out. You can
also magnify a particular part of an image (GR-D90/
D70 only pg. 35).
At any time, pressing
4
/6 7 resumes normal
playback.
Slow-Motion Playback/Playback Special Effects/
Playback Zoom:
Available only with the remote control (provided with
GR-D90/D70 only, pg. 35)
To Control The Speaker Volume:
Rotate the MENU/VOLUME wheel % so that the
volume level indicator T on the display moves to obtain
the appropriate volume.
ATTENTION
During Shuttle Search, parts
of the picture may not be
clearly visible, particularly on
the left side of the screen.
TAPE PLAYBACK
12: 34: 24
1 GR-D90/70/30US EN 12-16 02.11.6, 3:10 PM14
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC GR-D90 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC GR-D90 in the language / languages: English as an attachment in your email.

The manual is 2,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info