533227
11
Zoom out
Zoom in
Previous page
1/48
Next page
EN
11
OFF
(
CHARGE
)
PLAY
w
$
t y
r
180°
90°
o
20
5
m
h
1h30m
1h29m
0h03m
1h30m
0h02m (Blinking)
0h01m (Blinking)
0h00m (Blinking)
( )
Now
calculating
During shooting
Basic Recording
Perform the procedures listed below before continuing.
Power ( pg. 7)
Grip Adjustment ( pg. 8)
Viewfinder Adjustment (
pg. 8)
Load A Cassette (
pg. 9)
Recording Mode Setting ( pg. 10)
1 Remove the lens cap.
Pull on bottom end o of LCD monitor to open.
2 Set the Power Switch y to “ or ” while
pressing down the Lock Button
t located on the
switch.
Shooting while using the LCD monitor: Open the
LCD monitor fully.
Shooting while using the viewfinder: Pull out the
viewfinder fully.
The POWER/CHARGE lamp r lights and the
camcorder enters the Record-Standby mode. “PAUSE”
^ is displayed.
The image will not appear simultaneously on the LCD
monitor and the viewfinder. See “PRIORITY” in the
SYSTEM Menu ( pg. 23).
3 Press the Recording Start/Stop Button w. “
%, ^ appears and the tally lamp 3 lights while
recording is in progress.
To Stop Recording, press the Recording Start/Stop
Button w. The camcorder re-enters the Record-
Standby mode.
To Adjust The Brightness Of The Display
1. Make sure the Power Switch y is set to ” and
open the LCD monitor fully, then press the MENU/
VOLUME wheel $ in. The Menu Screen appears.
2. Rotate the MENU/VOLUME wheel $ to select
(CAMERA DISPLAY)” and press it.
3. Rotate the MENU/VOLUME wheel $ to select
“BRIGHT” and press it. The Menu Screen closes and
the bright level indicator 7 appears on the display.
To cancel, press the MENU/VOLUME wheel $
again so that the bright level indicator 7 disap-
pears.
4. Rotate the MENU/VOLUME wheel $ until the bright
level indicator 7 moves and the appropriate
brightness is reached, then press it. The bright level
indicator 7 disappears.
It is also possible to adjust the brightness of the
viewfinder by closing the LCD monitor, pulling out
the viewfinder and adjusting as described above.
TAPE RECORDING
NOTES:
If the Record-Standby mode continues for 5 minutes, the
camcorder’s power shuts off automatically. To turn the
camcorder on again, push back and pull out the
viewfinder again or close and re-open the LCD monitor.
When a blank portion is left between recorded scenes on
the tape, the time code is interrupted and errors may
occur when editing the tape. To avoid this, refer to
“RECORDING FROM THE MIDDLE OF A TAPE”
(
pg. 13).
To turn the tally lamp
3 or beep sounds off,
pg. 23.
When you use the LCD monitor outdoors in direct
sunlight, the LCD monitor may be difficult to see. If this
happens, use the viewfinder instead.
Black spots or bright spots of light (red, green or blue)
may appear constantly on the LCD monitor or the
viewfinder (
pg. 35).
When the Recording Start/Stop button
w is pressed, it
may take a few seconds before actual recording starts.
% starts rotating when the camcorder actually
starts recording.
The time required to calculate and display the remaining
tape length, and the accuracy of the calculation, may vary
according to the type of tape used.
“TAPE END” appears when the tape reaches its end, and
the power goes off automatically if left in this condition for
5 minutes. “TAPE END” also appears when a cassette at
its end is loaded.
Tape remaining time
indicator (Approximate)
Display
01 D50/40/30/20EK 11-15 02.12.4, 19:0911
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC GR-D40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC GR-D40 in the language / languages: English as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JVC GR-D40

JVC GR-D40 User Manual - German - 48 pages

JVC GR-D40 User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info