533230
46
Zoom out
Zoom in
Previous page
1/56
Next page
EDITING
46 EN
MasterPage: Left
The audio track can be customised only when
recorded in the 12-BIT and SP modes.
( pg. 32)
Use the provided remote control.
1 Play back the tape to locate the point where
editing will start, then press PAUSE (9).
2 While holding A. DUB (D) on the remote
control, press PAU SE (9). The “9D” and “MIC”
indicators appear.
3 Press PLAY (U), then begin “narrating”.
Speak into the microphone.
To pause dubbing, press PAUSE (9).
4 To end Audio Dubbing, press PAUSE (9),
then STOP (8).
To hear the dubbed sound during playback
Set “NARRATION” to “ON” or “MIX”.
( pg. 31, 35)
NOTES:
Sound is not heard from the speaker during Audio
Dubbing.
When editing onto a tape that was recorded at
12-BIT, the old and new soundtracks are recorded
separately.
If you dub onto a blank space on the tape, the
sound may be disrupted. Make sure you only edit
recorded areas.
If feedback or howling occurs during TV playback,
move the camcorder’s microphone away from the
TV, or turn down the TV’s volume.
If you change from 12-BIT to 16-BIT in mid-
recording and then use the tape for Audio
Dubbing, it is not effective from the point where
16-BIT recording began.
During Audio Dubbing, when the tape moves to
scenes recorded in the LP mode, scenes
recorded in 16-BIT audio or a blank portion, Audio
Dubbing stops.
Audio dubbing is also possible using an optional
microphone connected to the MIC connector.
While an optional microphone is connected, the
built-in microphone is disabled.
To perform Audio Dubbing with a video unit
connected to the camcorder’s S/AV connector,
first set “S/AV INPUT” to “A/V IN” or “S IN” in
VIDEO Menu. ( pg. 31, 36)
The “AUX” indication appears instead of “MIC”.
You can record a new scene into a previously
recorded tape, replacing a section of the original
recording with minimal picture distortion at the in
and outpoints. The original audio remains
unchanged.
Use the provided remote control.
NOTES:
Before performing the following steps, make sure
that “TIME CODE” for “CAMERA DISPLAY” and
“VIDEO DISPLAY” is set to “ON”. ( pg. 31, 34, 36)
Insert Editing is not possible on a tape recorded in
the LP mode or on a blank portion of a tape.
1 Play back the tape, locate the Edit-Out point
and press PAUSE (9). Confirm the time code at
this point. ( pg. 19)
2 Press REW (
3
) until the Edit-In point is
located, then press PAUSE (9).
3 Press and hold INSERT (I) on the remote
control, then press PAUSE (9). The “9I
indicator and the Time Code (min.:sec.) appear
and the camcorder enters Insert-Pause mode.
4 Press START/STOP to begin editing.
Confirm the insert at the time code you checked in
step 1.
To pause editing, press START/STOP. Press it
again to resume editing.
5 To end Insert Editing, press START/STOP,
then STOP (8).
NOTES:
Program AE with special effects ( pg. 42) can
be used to spice up the scenes being edited
during Insert Editing.
During Insert Editing, the date and time
information changes.
If you perform Insert Editing onto a blank space on
the tape, the audio and video may be disrupted.
Make sure you only edit recorded areas.
During Insert Editing, when the tape moves to
scenes recorded in the LP mode or a blank
portion, Insert Editing stops. ( pg. 50)
Audio Dubbing
PAUSE
PLAY
A.DUB
STOP
REW
INSERT
START/
STOP
Microphone
Connector
Speaker
Stereo Microphone
Insert Editing
GR-D290_270AS_07Advanced.fm Page 46 Thursday, March 24, 2005 12:12 PM
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC GR-D290 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC GR-D290 in the language / languages: English as an attachment in your email.

The manual is 3,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JVC GR-D290

JVC GR-D290 User Manual - German - 56 pages

JVC GR-D290 User Manual - Dutch - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info