595788
16
Zoom out
Zoom in
Previous page
1/164
Next page
16 EN
25min
120min 119min
3min
2min (Blinking)
1min (Blinking)
0min (Blinking)
* min.....(Now calculating)
RECORDING
Basic Recording
NOTE:
You should already have performed the procedures listed
below. If not, do so before continuing.
Power (
Z
pg. 8)
Tape Length (
Z
pg. 12)
Recording Mode Setting (
Z
pg. 13)
Grip Adjustment (
Z
pg. 14)
LOAD A CASSETTE
1
Slide EJECT to open the cassette holder, then insert
the cassette with the label facing out. Press PUSH to
ensure the holder is closed and locked.
ENTER RECORD–STANDBY MODE
2
Slide the LENS COVER open/close switch to open
the lens cover, then set the power switch to
“CAMERA”.
The power indicator lights and the camcorder
enters the Record–Standby Mode.
The scene you’re aimed at appears on the
viewfinder screen, with the word “PAUSE”
superimposed upon it.
START SHOOTING
3
Press the RECORDING START/STOP button.
•The tally lamp lights while recording is in progress,
and “
REC
” appears in the viewfinder.
If you want to turn the tally lamp off, see page 31.
STOP RECORDING
4
Press the RECORDING START/STOP button again to
stop recording.
The camcorder re-enters the Record-Standby
mode.
LENS COVER
SWITCH
NOTES:
A cassette holder can’t be opened unless a power supply is attached.
There may be a delay after you slide EJECT until the holder opens. Do not use force.
The tape’s remaining time is displayed in the viewfinder as shown.
The indicated remaining time is approximate.
The time required to calculate the remaining tape length, and the accuracy of the calculation, may vary
according to the type of tape used.
The tape remaining time displayed in the viewfinder is correct only if the correct tape length has been
selected (
Z
pg. 12).
“TAPE END” appears when the tape reaches its end, and the power goes off automatically if left in this
condition for 5 minutes. “TAPE END” also appears when a cassette whose tape is already at its end is
loaded.
If the Record–Standby mode continues for 5 minutes without performing Zoom or any other operations,
the camcorders power shuts off automatically. Set the Power switch to “POWER OFF”, and then back to
“CAMERA” to turn the camcorder on again.
If you’re recording on a cassette from the middle, use the RETAKE function (
Z
pg. 18) to find the end of
the last recording so you don’t erase any of it.
The LENS COVER warning blinks for about 8 seconds when the camcorder is turned on, when the cover is
closed.
POWER
Start/Stop
The power indicator
Tally lamp
Tape remaining time indicator
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC GR-AX1027 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC GR-AX1027 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 2,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info