660750
14
Zoom out
Zoom in
Previous page
1/36
Next page
1414
Transparent Adjust the transparency of the level meter display against the image. Off, Background, All
Peak Hold Activates/deactivates the peak hold function of the level meter. Off, On
Lissajous Setting Lissajous setting
<Lissajous display example>
H Axis Channel(X) Select an EMBEDDED AUDIO CH to display on the horizontal axis of the Lissajous screen. 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11,
12, 13, 14, 15, 16
V Axis Channel(Y) Select the EMBEDDED AUDIO CH to display on the vertical axis of the Lissajous screen. 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11,
12, 13, 14, 15, 16
Position Select a position to display the screen. Lower Right, Lower Left,
Upper Left, Upper Right
Transparent Set the background of the screen to translucent. Off, On
Gain Specify the Lissajous gain. 0dB, +6dB, +12dB
Audio Delay Audio delay setting
Delay Delay EMBEDDED AUDIO of SDI input. 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10
*
1
Operates as SDI-1 during Dual Link input.
*
2
Memorized for each input.
Scope Setting*
1
Configure the settings for the wave form monitor, vector scope and histogram.
Item To do Setting value
Gain*
2
Adjust the input gain level. –10 to +10
Size*
3
Set the window size. Normal, Large
Position Select the window position. Lower Right, Lower Left
Upper Left, Upper Right
Transparent Activates/deactivates the function to make the window translucent. Off, On
Off
On
:
:
Normal
Translucent
Auto Off Set the function to turn off the window automatically 15 minutes after displayed. Off, On
Histogram Display Select the signal component for the histogram display. Y, R, G, B, RGB
Wave Display Select a wave form to be displayed for the wave form monitor. Y, Pb, Pr (HD signal)
Y, Cb, Cr (SD signal)
R, G, B (RGB signal)
Wave Filter Turn on/off the lowpass filter to put over the input wave form data. Flat (No filter)
Low pass
Wave Over Level Marking Turn on/off the function to change the wave form color of signals over the value specified in
“Wave Over Level”. (+ below)
Off, On
Wave Over Level Adjust the lower limit for the over level. 70 – 109
<Example of the histogram display> <Example of the wave form monitor> <Example of the vector scope>
<dark brightness
light >
Pixels
Image signals
Start End
Red White
Y
Mg
R
B
100% level
75% level
Cy
G
Yl
The start and the end of the gradient
correspond to 0% and 100% of the signal.
Ex.: When the luminance signal is Y, “Wave Over
Level Marking” is set to “On” and “Wave Over
Level” is set to “80”
• Thewaveformcolorofsignalsoverthevalue
specified in “Wave Over Level” turns red.
• Thedisplaydiffersdependingontheinput
signal or the “Wave Display” setting.
Ex.: When the color bar is displayed
*
1
The vector scope is not displayed when the input signals are RGB.
*
2
Unavailable for the histogram.
*
3
The size of the histogram can only be “Normal.”
Y
X
Menu Configuration (cont.)
DT-V24G2_EN.indb 14 2016/07/27 16:37:14
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC DT-V21G2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC DT-V21G2 in the language / languages: English as an attachment in your email.

The manual is 17,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JVC DT-V21G2

JVC DT-V21G2 User Manual - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info