660749
16
Zoom out
Zoom in
Previous page
1/36
Next page
1616
Standby Mode Select the operation status when the monitor is powered OFF (standby). Normal, Serial, SDI Out
Normal
Serial
SDI Out
:
:
:
Changes to Low Power Mode 30 seconds after powered OFF to reduce power consumption.
In this case, it cannot power on by external control.
Can power on by external control after powered OFF.
Can power on by external control after powered OFF. Furthermore, video will
be output from the SDI OUT terminal.
LCD Saver
Configure the setting for reducing damage to the LCD panel for long-time use. (+ on page 19)
Setting 1st Start Set the standby time. (unit: hours) 00h-24h
Work
Time
Set the time for performing the function. (unit: hours) 01h-06h
Contrast Set the contrast reduction. Normal, Save
Backlight Reduce the backlight brightness. Normal, Save
OSD
Contrast
Set the contrast reduction of the OSD display. Normal, Save
Side Mask Select whether to use the side mask.
* The Side Mask function works no matter whether the LCD Saver is active or stopped.
Off, On
reset Restore the default settings for all the items in “LCD Saver”.
Execute Execute the LCD Saver function.
Cancel Stop the LCD Saver function. (“Cancel” will be grayed out during the function stop.)
Status Display the LCD Saver status. Off, Ready
Start After Display required time until the LCD SAVER operation starts. (unit: hours and minutes) **h **min
Function Key Setting
Specify the function assigned to the F1/F2 button.
Function1
Function2
Specify the function assigned to the F1/F2 button.
* For details on the functions set up, see the menu description (pages 11 to 18).
- - -, Aperture, I/P Mode,
Frame, Center Marker, Level
Meter Display, Gamma, Color
Temperature, CRC Error,
Manual Aspect, Picture
Memory Mode
Function Display Select whether to display the status of the assigned function when you press the F1 button. Off, Mode-1, Mode-2
Off
Mode-1
Mode-2
:
:
:
No status display. Perform the registration function.
Display the status. Perform the registration function.
Display the status. Do not perform the registration function.
Perform the registration function when the status is displayed and the button is
pressed again.
l
To display the “Function Key Setting” menu, press the button when the menu is not displayed.
l About the operations of F1/F2 button
Each time you press the button, the setting value for the assigned function changes in order.
Ex: When “Color Temperature” is assigned
Each time you press the button, four setting values alternate.
Picture Sub Adjust
Configure the standard level of image adjustment.
Item To do Setting value
Contrast*
1
Adjust the standard level for the contrast adjusted with the CONTRAST knob on the front
panel.
–20 to +20
Bright*
1
Adjust the standard level for the brightness adjusted with the BRIGHT knob on the front
panel.
–20 to +20
Chroma*
1
Adjust the standard level for the chroma adjusted with the CHROMA knob on the front panel. –20 to +20
Phase*
1,
*
2
Adjust the standard level for the phase adjusted with the PHASE knob on the front panel. –20 to +20
NTSC Setup Select the set-up level of the input NTSC signal. 00 (compliant with 0 %
set-up signal), 7.5 (compliant
with 7.5 % set-up signal)
Component Level Select the level of the analog component signal (480i only). B75 (compliant with
BetacamVTR 7.5 % set-up
signal), B00 (compliant with
BetacamVTR 0 % set-up
signal), SMPTE (compliant
with M2VTR signals)
sub menu Display the sub menu which enables you to adjust the items in “Picture Sub Adjust” while viewing the actual picture.
reset Restore the default settings for all the items in “Picture Sub Adjust”.
*
1
Memorized for each input.
*
2
When “Component Phase” (+ page 15) is set to “Disable,” “Phase” cannot be adjusted if no NTSC signal is input.
Menu Configuration (cont.)
DT-V24G2_EN.indb 16 2016/07/27 16:37:14
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC DT-V17G25 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC DT-V17G25 in the language / languages: English as an attachment in your email.

The manual is 17,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JVC DT-V17G25

JVC DT-V17G25 User Manual - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info