20741
32
Zoom out
Zoom in
Previous page
1/112
Next page
Filename [DR-M10U_06-2Initial Set.fm]
Masterpage:Left+
32 EN
Page 32 January 16, 2004 6:34 pm
INITIAL SETTINGS (cont.)
DBS Receiver
Control Setting
Place the DBS (Direct Broadcast Satellite) receiver on top
of the unit. Attach the unit’s Controller to the top of the
unit with the Controller’s transmitter pointed towards the
DBS receiver’s remote sensor.
A
TTENTION:
The Controller can also control a cable box. If both a DBS
receiver and a cable box are used, position the Controller so its
signal reaches the remote sensors of both the DBS receiver and
cable box.
The following procedure is required if you receive
satellite channels through a DBS (Direct Broadcast
Satellite) receiver. The Controller allows the unit to
automatically switch the DBS receiver’s channel during
timer recording.
NOTES:
The unit can automatically change the DBS receiver channels
using the Controller when the unit has been programed using
“Manual Timer Programing” (
pg. 64).
Because satellite programing does not use PlusCode, the
Controller cannot change the DBS receiver channels during
“VCR Plus+
®
Timer Programing” ( pg. 60).
If a cable box is also used, it is recommended that you
connect the DBS receiver to your unit’s audio/video input
connectors and the cable box to your unit’s antenna input
connector.
Installing Controller
A
Install a Controller.
Place a Controller so that the path between its transmitter
and the DBS receiver’s remote sensor is unobstructed.
B
Attach the Controller.
Fix securely using the adhesive strip attached on the back
of the Controller.
C
Make connections.
If your DBS receiver does not have audio/video output
connectors
Connect the RF output connector on the DBS receiver to
the ANTENNA IN connector on the rear of your unit.
If your DBS receiver has audio/video output connectors
Connect an audio/video cable between the AUDIO/
VIDEO INPUT connectors on the rear of the unit and the
audio/video output connectors on the DBS receiver.
NOTE:
When connecting your DBS receiver, refer to its instruction
manual.
D
Connect the Controller to unit.
Connect the Controller to the CABLE BOX connector on
the rear panel.
CABLE
BOX
DBS receiver
Controller
(suggested locations)
Transmitter
To
ANTENNA
IN
Your unit
Controller
DBS receiver
To RF
output
To Audio/
video
output
or
Your unit
To AUDIO/
VIDEO
INPUT
How to control the DBS receiver
This unit has two separate methods to control your DBS
receiver.
The unit’s wireless Remote can control your DBS receiver.
This eliminates the need for a separate DBS receiver’s
Remote.
The unit’s Controller can also control your DBS receiver.
This allows the unit to change your DBS receiver’s channel
number during timer recording.
Each method must be set up separately. To set up the unit’s
Remote, refer to page 94. To set up the Controller, go to
page 33.
DR-M10U_01.book Page 32 Friday, January 16, 2004 7:38 PM
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC DRM10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC DRM10 in the language / languages: English as an attachment in your email.

The manual is 9,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JVC DRM10

JVC DRM10 User Manual - German - 116 pages

JVC DRM10 User Manual - Dutch - 116 pages

JVC DRM10 User Manual - French - 116 pages

JVC DRM10 User Manual - Portuguese - 116 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info