56211
32
Zoom out
Zoom in
Previous page
1/100
Next page
Filename [MV5S_08Basic TimerDub.fm]
Masterpage:Left+
32 EN
TIMER RECORDING
Page 32Wednesday, 31 August 2005 16:55
On-Disc Timer Programming is a function used with discs that are
especially intended for a specific programme. The disc is then
programmed for a programme you always watch every day or
every week. Since older programmes are automatically
overwritten, a single DVD-RAM/RW (VR mode) disc can be used
without worrying about how much recording capacity remains.
( pg. 33)
You can programme each disc to timer-record as many as
8 programmes.
To Make The Disc For On-Disc Timer Programming
1 Load a recordable disc.
2 Press DVD so that the DVD lamp lights up on the unit.
3 Press PROG to access the Programme Check screen.
4 When On-Disc Timer Programming is made for the first
time on the disc
Press rt to select “DISC TIMER PRGM”, then press ENTER.
When some programmes are recorded on the disc, a caution
message appears. In such a case, backup the programmes as
required, then format the disc before making On-Disc Timer
Programming. ( pg. 89)
When On-Disc Timer Programming has already been made on
the disc
Press rt to select “NEW TIMER PROGRAMME”, then press
ENTER.
5 Press rt to set the desired date.
The current date appears on the TV screen. The date you enter
appears in its place.
6 Press we to select “START”, then press rt to set the desired
start time.
Each press of rt advances/goes back the start time in 1-min.
increments.
To advance/go back the start time in 30-min. increments, press and
hold rt.
7 Press we to select “STOP”, then press rt to set the desired
stop time.
Each press of rt advances/goes back the stop time in 1-min.
increments.
To advance/go back the stop time in 30-min. increments, press and
hold rt.
8 Press we to select “TV PROG”, then press rt to select the
desired channel.
9 Set “DAILY/WEEKLY” option.
Refer to step 6 in “SHOWVIEW™ Timer Programming” ( pg. 29).
It is necessary to set “DAILY/WEEKLY” option for On-Disc Timer
Programming. ( pg. 30, “Weekly/Daily Recording”)
10 Set the other recording options as required.
You can select XP, SP, LP, EP or FR480 mode for “REC MODE”.
However, you cannot select FR (JUST), FR60–FR360 and FR420.
Refer to step 6 in “SHOWVIEW™ Timer Programming” ( pg. 29).
It is not possible to use the Free Rate function. ( pg. 62)
11 Press ENTER to access the Programme Confirmation screen.
12 Press ENTER to complete timer programming.
To programme another timer, repeat steps 3 12.
To Timer-record The Programme With The Programmed Disc
1 Load a programmed disc.
2 Press TIMER #. The unit turns off and “ appears on
the front display panel. The DVD timer indicator also lights up on
the unit and the unit is automatically turned off.
To disengage the timer mode, press TIMER # again.
NOTES:
On-Disc Timer Programming is not possible on a DVD-RW disc
formatted in video mode. ( pg. 89)
The information of a programme recorded with On-Disc Timer
Programming is not stored in the library. ( pg. 71)
The play list is not created for the programmes recorded with On-Disc
Timer Programming. (
pg. 68)
Basic Recording (
pg. 26), SHOWVIEW Timer Programming
( pg. 29), Manual Timer Programming ( pg. 31) are not possible
on the On-Disc Timer programmed disc.
The beginning of a programme may not be recorded. Also, if the 1st
programme’s recording stop time and the 2nd programme’s recording
start time is the same, the ending of the 1st programme may not be
recorded.
If there is a power cut while recording, the recordings before the
power cut are not guaranteed.
On-Disc Timer Programming (DVD Deck
Only)
Make sure that the unit’s built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
A
TTENTION:
On-Disc Timer Programming is possible only with the disc for On-
Disc Timer Programming.
If data is recorded on a disc for On-Disc Timer Programming using
a unit from another manufacturer, On-Disc Timer Programming
may no longer function properly.
rtwe
ENTER
PROG
TIMER
DVD
Satellite Receiver Users
To timer-record a satellite broadcast using the On-Disc Timer
Programming function:
A Perform “On-Disc Timer Programming (DVD Deck Only)”.
B Set the satellite receiver to the appropriate channel before
the selected programme begins.
C Select “L-2” in step 8.
D Leave the satellite receiver’s power on.
MV5S_00.book Page 32 Wednesday, August 31, 2005 4:55 PM
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC DR-MV5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC DR-MV5 in the language / languages: English as an attachment in your email.

The manual is 10,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JVC DR-MV5

JVC DR-MV5 User Manual - German - 100 pages

JVC DR-MV5 User Manual - Dutch - 100 pages

JVC DR-MV5 User Manual - French - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info