57095
13
Zoom out
Zoom in
Previous page
1/24
Next page
(No.YD006)1-13
4.3 Electrical adjustment
Note:
The following adjustment procedures are not only necessary
after replacement of consumable mechanical parts or board
assemblies, but are also provided as references to be referred
to when servicing the electrical circuitry.
In case of trouble with the electrical circuitry, always begin a
service by identifying the defective points by using the measur-
ing instruments as described in the following electrical adjust-
ment procedures. After this, proceed to the repair,
replacement and/or adjustment. If the required measuring in-
struments are not available in the field, do not change the ad-
justment parts (variable resistor, etc.) carelessly.
4.3.1 Servo circuit
4.3.1.1 Switching point
(1) Play back the signal (A1) of the alignment tape (A2).
(2) Apply the external trigger signal to D.FF (E) to observe the
VIDEO OUT waveform and V.PB FM waveform at the
measuring points (D1) and (D2).
(3) Set the VCR to the manual tracking mode.
(4) Adjust tracking so that the V.PB FM waveform becomes
maximum.
(5) Set the VCR to the Auto adjust mode by transmitting the
code (F) from the Jig RCU. When the VCR enters the stop
mode, the adjustment is completed.
(6) If the VCR enters the eject mode, repeat steps (1) to (5)
again.
(7) Play back the alignment tape (A2) again, confirm that the
switching point is the specified value (G).
Fig.4-3a Switching point
4.3.1.2 Slow tracking preset
(1) Record the signal (A2) in the mode (B1), and play back
the recorded signal.
(2) Set the VCR to the manual tracking mode.
(3) Set the VCR to the FWD slow (+1/6x) mode.
(4) Transmit the code (F) from the Jig RCU to adjust so that the
noise bar becomes the specified value (G) on the TV
monitor in the slow mode.
(5) Set the VCR to the Stop mode.
(6) Confirm that the noise bar is (G) on the TV monitor in the
slow mode.
(7) Repeat steps (3) to (6) in the REV slow (+1/6x) mode.
(8) Repeat steps (1) to (7) in the mode (B2).
Note:
For FWD slow (+1/6x) playback, transmit the code “08”
from the Jig RCU to enter the slow playback mode, and
transmit the code “D0”for REV slow (-1/6x) mode.
4.3.2 DVD Video circuit
Note
when perform these adjustments, set the unit to DVD
mode.(DVD lamp lights up)
4.3.2.1 EE COMPONENT Y level
(1) Observe the Y OUT waveform at the measuring point (D).
(2) Set the VCR to the EVR mode by transmitting the code (F1)
from the Jig RCU.
(3) Set the EVR address to (F2) by transmitting the code (F3)
from the Jig RCU.
(4) Transmit the code (F4) from the Jig RCU to adjust so that
the Y level of the Y OUT waveform becomes the specified
value (G).
(5) Release the EVR mode of the VCR by transmitting the
code (F5) from the Jig RCU again. (When the EVR mode
is released, the adjusted data is memorized.)
Fig.4-3b EE componet Y level
Signal (A1)
(A2)
Stairstep signal
Alignment tape(EP,stairstep,NTSC) [MHP-L]
Mode (B) PB
Equipment (C) Oscilloscope
Measuring point (D) VIDEO OUT terminal (75 ohm terminated)
TP106 (PB. FM)
External trigger (E) TP111 (D.FF)
Adjustment part (F) Jig RCU: Code “5A”
Specified value (G) 6.5 ± 0.5H
Adjustment tool (H) Jig RCU [PTU94023B]
Signal (A1)
(A2)
Ext. input
Color (colour) bar signal [NTSC]
Mode (B1)
(B2)
VHS SP
•VHS EP
Measuring point (D) TV-Monitor
Adjustment part (F) Jig RCU: Code “71”or “72”
Specified value (G) minimum noise
Adjustment tool (H) Jig RCU [PTU94023B]
V.sync
Trigger point
Switching point
V. rate
Signal (A) Internal color bar
Mode (B) EE
Equipment (C) Oscilloscope
Measuring point (D) COMPONENT Y terminal
EVR mode
EVR address
(F1)
(F2)
(F3)
(F4)
(F5)
Jig code “95”
"ADJUST01 : **"
Jig code “21”
Jig code “18” or “19” (Channel +/-)
Jig code “3C”
Specified value (G) 1.00 ± 0.02 Vp-p (terminated)
Adjustment tool (H) Jig RCU [PTU94023B]
Y level
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC DR-MV1SUC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC DR-MV1SUC in the language / languages: English as an attachment in your email.

The manual is 1,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info