57388
82
Zoom out
Zoom in
Previous page
1/92
Next page
Filename [MH30_20S_12Subsidiary.fm]
Masterpage:Left+
82 EN
TROUBLESHOOTING
Page 82Thursday, 7 April 2005 10:14
Recording (HDD Deck)
AL-1B, AL-2B or AF-1B has been selected as the input mode.
N Set to the desired channel.
The camcorder has not been properly connected.
N Confirm that the camcorder is properly connected.
The input mode is not correct.
N Set the input mode to AF-1B. (A pg. 62)
Timer Recording
Date and time is not correct.
N Set date and time correctly. (A pg. 77)
Timer recording is in progress.
N Timer programming can’t be performed while a timer recording
is in progress. Wait until it finishes.
Date and time is not correct.
N Set date and time correctly. (A pg. 77)
Date and time set on the unit is not correct.
N Set date and time correctly. (A pg. 77)
The channel position does not correspond to that in the
receiving area.
N Set the correct channel position for the receiving broadcast.
(A pg. 73)
The unit’s channel positions have been set incorrectly.
N Refer to AS
HOWVIEW System SetupB (A pg. 73) and reperform
the procedure.
The satellite receiver is not connected properly to this unit.
N Connect the satellite receiver to the [L-2 IN/DECODER]
connector properly. (A pg. 49)
Power failure occurred.
N Set date and time correctly. (A pg. 77)
32 programmes have already been timer programmed.
N Clear unnecessary programmes on the unit, then try timer
programming again. (A pg. 48)
The PC’s data recorded on a DVD-RAM drive cannot be
cleared on this unit.
N Format the disc. (When the disc is soiled, wipe the disc with a
soft dry cloth before formatting.) (A pg. 9, 78)
Other Problems
For basic connection
N Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator (q) lights off on the front display panel.
For component video connection
N Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator (q) lights up on the front display panel.
The camcorder’s microphone is too close to the TV.
N Position the camcorder so its microphone is away from the TV.
The TV’s volume is too high.
N Turn the TV’s volume down.
Those channels have been designated to be skipped.
N If you need the skipped channels, restore them. (A pg. 75)
Recording or RetroActive recording* is in progress.
N Press W to pause recording, change the channel, then press I
to resume recording.
* HDD deck only
After the manual settings were made, Auto Channel Set was
performed.
N Perform AClock SetB (A pg. 77).
N Reset the unit by disconnecting the AC power plug from the AC
outlet and connect again.
TV broadcasts cannot be recorded.
Camcorder recording is not possible.
Timer programming cannot be made.
Timer programming recording does not start.
SHOWVIEW Timer Programming cannot be made.
The SHOWVIEW system does not timer record properly.
Automatic Satellite Programme Recording does not start.
On the front display panel, A––:B appears.
APROGRAMME FULLB appears on the TV screen during timer
programming.
The disc space does not increase when recorded titles are
cleared.
The image of the TV broadcast appears distorted on the TV
screen.
Whistling or howling is heard from the TV during camcorder
recording.
When scanning channels, some of them are skipped over.
The channel cannot be changed.
Channel settings that were made manually seem to have
changed or disappeared.
Malfunction occurs and the unit cannot be power off.
MH30_20S_00.book Page 82 Thursday, April 7, 2005 10:14 AM
82


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC DR-MH20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC DR-MH20 in the language / languages: English as an attachment in your email.

The manual is 6,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JVC DR-MH20

JVC DR-MH20 User Manual - German - 92 pages

JVC DR-MH20 User Manual - Dutch - 92 pages

JVC DR-MH20 User Manual - French - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info