660672
15
Zoom out
Zoom in
Previous page
1/64
Next page
Installing the Projector
Precautions during Installation
Please read the following carefully before installing this
unit.
Do not install at the following
This unit is a precision device. Please refrain from
installing
or using it at the following locations. Otherwise,
it may cause fire or malfunction.
0
Dusty, wet and humid places
0
Places subject to oily smoke or cigarette smoke
0
On top of a carpet or bedding, or other soft surfaces
0
Places exposed to direct sunlight
0
Places with a high or low temperature
0
Do not install this unit in a room that is oily or subject
to
cigarette smoke. Even a small quantity of smoke or
oiliness can have a long-term impact on this unit.
* This unit produces a great amount of heat, and is
designed to take in cool air to cool its optical
components. Using the unit at the above locations
may cause dirt to attach to the light path, thereby
resulting in dark images or dull colors.
*
Dirt that sticks to the optical components cannot be
removed.
Maintain clearance from the wall, etc.
As the unit discharges a large amount of heat, install it
with adequate clearance from the surroundings as shown
below.
.
Front
150 mm
and above
200 mm
and above
300 mm
and above
300 mm
and above
150 mm and above
Leave the front area of the unit unblocked.
If there is any obstructing object in front of the exhaust
vent,
hot air will flow back to the unit and cause it to heat
up. Hot air flowing out of the unit may cast shadows on
the screen (heat haze phenomenon).
Using the projector
This
unit uses a projection lamp, which will heat up when
in use.
Please refrain from projecting in the following
circumstances. Otherwise, it may cause fire or
malfunction.
0
Projection with the unit stood vertically
.
0
Projection with the unit inclined at an angle
Install the unit such that the tilt in the horizontal direction
(left or right) is within ±10
°.
.
10° 10°
As shown in the illustration, this unit can be installed with
a tilted angle, but for some areas there might be other
conditions. Moreover, depending on the angle of
installation,
it may be necessary to have a hanging metal
mount and secure installation base depending on the
angle of the installation.
.
Area B
Area B
Area A
45 °
90 °
30 °
-30 °
Area A
:
Use the factory-installed lamp. The lamp is
attached to the Area A attachment (X mark
and “0°” marking).
Area B
:
Replace with the supplied attachment (+
mark and “90
°” marking).
Refer to p. 42 on the replacement
procedures.
15
Set up
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC DLA-VS2400ZG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC DLA-VS2400ZG in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info