521282
67
Zoom out
Zoom in
Previous page
1/80
Next page
English 67
Accessories/Installation Procedure
Accessories
1
..........1
2
..........1 (2m)
3
..........8
4*
1
..........1 (3m)
*
1
DDX630WBT/
DDX630WBTM only.
Installation Procedure
1 To prevent a short circuit, remove the key
from the ignition and disconnect the
-
battery.
2 Make the proper input and output wire
connections for each unit.
3 Connect the speaker wires of the wiring
harness.
4 Connect the wiring harness wires in the
following order: ground, battery, ignition.
5 Connect the wiring harness connector to
the unit.
6 Install the unit in your car.
7 Reconnect the
- battery.
8 Press the reset button.
9 Perform the Initial Setup.
2WARNING
If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may
start a fire. Always connect those wires to the
power source running through the fuse box.
Do not cut out the fuse from the ignition wire
(red) and the battery wire (yellow). The power
supply must be connected to the wires via the
fuse.
After the Installation
After the installation, perform the Initial Setup
by referring to the instruction manual.
¤
Mounting and wiring this product requires
skills and experience. For best safety, leave the
mounting and wiring work to professionals.
Make sure to ground the unit to a negative 12V
DC power supply.
Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
Do not use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
If the power is not turned ON (“Miswiring
DC Offset Error, “Warning DC Offset Error is
displayed), the speaker wire may have a short-
circuit or touched the chassis of the vehicle and
the protection function may have been activated.
Therefore, the speaker wire should be checked.
If your cars ignition does not have an ACC
position, connect the ignition wires to a power
source that can be turned on and off with the
ignition key. If you connect the ignition wire to
a power source with a constant voltage supply,
such as with battery wires, the battery may be
drained.
If the console has a lid, make sure to install the
unit so that the faceplate will not hit the lid when
closing and opening.
If the fuse blows, first make sure the wires aren’t
touching to cause a short circuit, then replace the
old fuse with one with the same rating.
Insulate unconnected wires with vinyl tape or
other similar material. To prevent a short circuit,
do not remove the caps on the ends of the
unconnected wires or the terminals.
Never cut away cable insulation to make the
proper connections may result in fire or product
damage.
Connect the speaker wires correctly to the
terminals to which they correspond. The unit may
be damaged or fail to work if you share the -
wires or ground them to any metal part in the car.
EN_LVT2272-001A_MX_200mm.indb 67EN_LVT2272-001A_MX_200mm.indb 67 11/12/15 13:0411/12/15 13:04
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC DDX630 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC DDX630 in the language / languages: English as an attachment in your email.

The manual is 10,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info