656268

Just Fire NB-B24 Manual

10
Zoom out
Zoom in
Previous page
1/41
Next page
PELLET BURNING STOVES
INSTALLATION AND MAINTENANCE MANUAL
10
compromising thermodynamic performance, however it is required that the conditions still guarantee about 50 m³ / h of air
replacement, as provided in the current UNI 10683 .
2.5. CONNECTION OF SMOKE DISCHARGE PIPE
When making the hole for the flue pipe it must be taken into account the possible
presence of inflammable materials. If the hole has to go through a wood wall or other
thermo labile material , the installer MUST use the Industrial insulated pipe (with min
thermal conductivity of 0.07 W / m ° K). The same applies if the stove pipe must go vertical
or horizontal sections remain near (min.20cm) to a heat-labile wall.
The combustion chamber works in depression, so the exhaust duct for the exhaust fumes
will be linked to depression when effective chimney as prescribed.
It should always use pipes and fittings with appropriate seals to ensure
air-tightness in order to avoid possible harmful CO fumes into the environment.
All sections of the exhaust duct must be inspectable and removable to
allow for periodic cleaning of the interior, which is necessary for the proper functioning
of the system (T-piece with inspection). Position the stove strict accordance with all
regulatory requirements and attention to highlighted date.
IMPORTANTE!
All changes direction 90 degrees of the flue gas channel must be prepared if possible
with the appropriate fittings to "T" with inspection. It is absolutely forbidden to use a
net at the end of the hose as it can cause serious problems for the proper and safe operation of the stove.
In connection do not use the chimney sections of pipe horizontally, but always the same place at an angle of 5° minimum to
rise, possibly avoiding the use of a 90-degree (you can use upto 3), and use preferably 45 ° curves. It is recommended to not
use a total length of the pipe diameter 80 mm, greater than 6 m in total.
2.6. CONNECTION TO THE CHIMNEY
The chimney must have inside dimensions of no more than cm. 20X20 or 20 cm
diameter. In the case of larger or poor condition of the chimney (ie: cracks, poor
insulation, etc.) it is recommended to insert stainless steel tube in the chimney of a of
suitable diameter for its entire length, to the very top. Check with suitable
instruments that there is a minimum draft. Guaranteed 15 Pa. At the bottom of a
chimney inspection for periodic inspection and cleaning, which must be done
annually. You must ensure that a chimney top is installed according to regulations for
wind force.
This type of connection must guarantee of 15 Pa, allows the correct discharge of
smoke with a natural draft even if there is no electricity.
2.7. CONNECTION TO AN EXTERNAL FLUE PIPE WITH ISOLATED OR DOUBLE WALL
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Just Fire NB-B24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Just Fire NB-B24 in the language / languages: English as an attachment in your email.

The manual is 4,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info