519527

Junkers TW 2 Manual

8
Zoom out
Zoom in
Previous page
1/104
Next page
8
TW2
English
3 Mounting
Before starting to work, the power supply
(230 V, 50 Hz) to the heating equipment
must be interrupted.
3.1 Choose a suitable installation site
(if room thermostat function is to
be used).
Important for the regulating quality of the remote
control is the selection of a suitable mounting lo-
cation.
Anforderungen
• The room in which it is mounted must be suit-
able for controlling the temperature of the
complete heating system.
• The radiators installed in the room should not
be equipped with thermostatic valves.
Note: It is more effective to install hand valves
that can be preset so that the output of
the radiator in the room where the TW 2
is mounted can be set as low as possi-
ble.
There must be sufficient space below the con-
trol unit to allow air to circulate unrestricted
through the ventilation slots (shaded area in Fig-
ure ).
Note: observe the recommended clearances
as shown in Figure .
3.2 Fitting the Remote Control
– For mounting, pull the upper part of the re-
mote control (a) from the base (b).
– The base (b) of the TW 2 can be mounted ei-
ther with two screws (d) on a standard flush
connection box (c) of 55 mm dia. (Fig. ),
or
– with plugs (6 mm) and screws (3.5 mm dia.,
oval head), screwed directly onto the wall
(Fig. , drilling template enclosed).
4 Electrical Connection
The TW2 remote control unit is connected to
the outside-temperature controlled programmer
by means of two cores in the connecting lead
(24 V).
– Observe the applicable regulations.
– Use electrical cable conforming at least to
H05VV-... with a cross-sectional area of
1.5 mm
2
.
– Connect the remote control unit to the cen-
tral heating appliance according to the wiring
diagram (see Figs. to ).
Avoiding Interference
– Route the connecting leads separately from
wires carrying 230 V/400 V (minimum sepa-
ration 100 mm).
– If there are external sources of inductive inter-
ference (e.g. high power cables, overhead
tram cables, transformer substations, radio
and television sets, amateur radio equipment,
microwave appliances, etc.) the wires carry-
ing the control signals should be shielded.
4.1 Commissioning
– After connecting the electrical wiring, press
outer cover (a) onto base (b).
– Switch on the central heating appliance.
5 Operation
The TW2 is not an independent regulator but
rather a remote control with or without room
temperature sensing.
It shifts the heating curve of the outside-temper-
ature controlled programmer as required.
It is therefore important that the settings on the
regulator (e.g., heating curve) are correct.
Note: The mode switch on the outside-tem-
perature controlled programmer must
be set to position . The text display
must be set to Automatic.
2
2
4
5
6 10
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Junkers TW 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Junkers TW 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Turkish, Spanish as an attachment in your email.

The manual is 1,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Junkers TW 2

Junkers TW 2 User Manual - Dutch, French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info