636977
10
Zoom out
Zoom in
Previous page
1/29
Next page
Bild 11
Zur Montage Abdeckhaube (AF
c
) abzie-
hen und das Fühlergehäuse (AF
a
) mit
zwei Schrauben (AF
g
) an der Außen-
wand befestigen.
4.5 Montage des Reglers
Den Regler (l) auf den Sockel (k) stek-
ken und mit den beiden Befestigungs-
schrauben (m) rechts oben und links un-
ten festschrauben (Bild 7).
4.6 Montage des Zubehörs
4.6.1 Montage der Einbauschaltuhr
EU1ToderEU1W(Zubehör)
Staubschutzdeckel (n) abnehmen und
Abdeckung des Uhrenschachts (o) mit
einem Schraubenzieher vorsichtig ent-
fernen (Bild 7).
Bild 12
Einbauschaltuhr (w) wie in Bild 12 in
den Uhrenschacht schieben.
Einbauschaltuhr (w) mit den zwei
Schrauben (x) befestigen.
Die Abdeckung (o) wird nicht mehr be-
nötigt (Bild 7).
4.6.2 Montage von Fernbedienung
und mechanischer Vorlauftem-
peraturbegrenzer (Zubehör)
Fernbedienung und mechanischer Vor-
lauftemperaturbegrenzer entsprechend
den zugehörigen Einbauvorschriften
montieren.
5. Elektrischer Anschluß
Folgende Leitungsquerschnitte sind zu
verwenden:
Vom TA 21 A1 zum Außentemperatur-
fühler:
bis20m: 0,75bis1,5mm²
bis 30 m: 1,0 bis 1,5 mm²
über 30 m: 1,5 mm²
Vom TA 21 A1 zur Fernbedienung:
1,5 mm²
Unter Berücksichtigung der geltenden
Vorschriften müssen für den Anschl
des Außentemperaturfühlers und der
Fernbedienung mindestens Elektrokabel
der Bauart H05VV-... eingesetzt werden.
Alle 24-V-Leitungen (Meßstrom) müssen
von 230 V oder 400 V führenden Leitun-
gen getrennt verlegt werden, damit keine
induktive Beeinflussung stattfindet (Min-
destabstand 100 mm).
Sind induktive äußere Einflüsse z. B.
durch Starkstromkabel, Fahrdrähte, Tra-
fostationen, Rundfunk- und Fernsehge-
räte, Amateurfunkstationen, Mikrowellen-
geräte, o. ä. zu erwarten, so sind die
Meßsignal führenden Leitungen ge-
schirmt auszuführen.
Je nach Zubehör sind die entsprechen-
den Schaltpläne zu befolgen:
4101-11.1/G
AF
c
AF
g
AF
e
AF
f
AF
a
AF
d
10
2470-15.1/O
x
xx
x
x
xx
x
w
w
w
w
l
ll
l
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Junkers TA 21 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Junkers TA 21 A1 in the language / languages: German as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info