617161
17
Zoom out
Zoom in
Previous page
1/24
Next page
Gasartenanpassung
6 720 608 075 (2006/05)
17
6 Gasartenanpassung
Die werkseitige Einstellung der Erdgasgeräte entspricht
EE-H bzw. EE-L.
Erdgas H (23)
Geräte der Erdgasgruppe 2E (2H) sind ab Werk auf
Wobbeindex 15 kWh/m
3
und 20 mbar Anschlussdruck
eingestellt und plombiert
Erdgas L (21)
Geräte der Erdgasgruppe 2LL sind ab Werk auf Wob-
beindex 12,2 kWh/m
3
und 20 mbar Anschlussdruck
eingestellt und plombiert
B Gasart-Umbausatz nach beiliegendem Einbauhinweis
einbauen.
B Nach jedem Umbau Gas-Einstellung vornehmen.
Gasart-Umbausätze
Soll ein Gerät mit einer anderen als auf dem Typschild
angegebenen Gasart betrieben werden, so ist ein
Umbausatz zu verwenden.
B Gasart-Umbausatz nach beiliegendem Einbauhinweis
einbauen.
B Nach jedem Umbau Gas-Einstellung vornehmen.
6.1 Gas-Einstellung (Erd- und Flüssiggas)
Die Nennwärmeleistung kann mit dem Düsendruck oder
volumetrisch eingestellt werden.
Immer zuerst bei maximaler Nennwärmebelastung und
dann bei minimaler Nennwärmebelastung einstellen.
6.2 Düsendruckeinstellung
B Mantelschale abnehmen.
B Verschlussschraube für Messtelle Dusendruck lösen
(Bild 17).
B Messgerät am Mess-Stutzen (Düsendruck) anschlie-
ßen.
Bild 17 Messpunkt Düsendruck
Düsendruck bei maximaler Heizleistung
1)
B Plombierung von der Einstellschraube entfernen
(Bild 18).
B Gerät einschalten. Leistungswähler auf Linksanschlag
drehen (maximale Leistung).
Bild 18 Einstellschraube max. Gasmenge
B Mehrere Warmwasserhähne öffnen.
B Mit der Einstellschraube (Bild 18) den Düsendruck
gemäß Tabelle 7 einstellen.
B Einstellschraube wieder plombieren.
Düsendruck bei minimaler Heizleistung
Werkseitig ist die Einstellung verplombt.
Eine Einstellung auf die Nennwärmebelas-
tung und min. Wärmebelastung nach TRGI
1986, Abschnitt 8.2 ist nicht notwendig.
Umbau von ... Best.-Nr.
WR11
21 in 23
8 719 002 274 0
23 in 21 8 719 002 273 0
23/21 in 31
8 719 002 278 0
31 in 21 8 719 002 280 0
31 in 23 8 719 002 279 0
WR14
21 in 23
8 719 002 275 0
23 in 21 8 719 002 276 0
23/21 in 31
8 719 002 281 0
31 in 21 8 719 002 283 0
31 in 23 8 719 002 282 0
WR18
23 in 21
8 719 002 277 0
21 in 31 8 719 002 284 0
Tab. 6
1) Verschlusschraube für Messtelle Düsendruck ver-
schließen Mantelschale montieren
Der minimale Düsendruck wird nach der
Einstellung des maximalen Düsendrucks
automatisch eingestellt.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Junkers Jetatherm COMPACT WRD 14 -2 .G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Junkers Jetatherm COMPACT WRD 14 -2 .G in the language / languages: German as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info