Manual Junker JD36AB50 (page 36 of 40) (English, German, Dutch, French, Italian)

636918

Zoom out

Zoom in

1/40

Preparing the wall cupboard

 Ensure that there is a minimum gap

between hob and extractor hood of 650

mm (for gas hobs) or 430 mm (for electric

hobs).

This extractor hood has been designed

for installation inside a wall cupboard with

the following dimensions:

Width: 600 mm

Depth: 280 bis 350 mm

Height: at least 300 mm.

Preparation:

1. Remove bottom panel of cupboard – if

ﬁtted.

 The stability of the cupboard must be

maintained.

2. Mark two points – right and left – on the

inside of the cupboard where the hood

is to be mounted, and start the hole with

a gimlet.

Details for drilling:

l 2 mm – max. 10 mm deep.

Attention:

❑ Use enclosed template

II for

marking points where hood is to be

mounted.

❑ The mounting points shown on the

template have been conﬁgured in such

a way as to allow a 20 mm thick handle

to be attached ﬂush with the front edges

of the cupboard.

❑ A stop allows the handle (Dimension Δ)

to be positioned further forwards.

600

170

280-350

mind

300.

If the cupboard depth is greater than

280 mm, the hood can be mounted further

back,

. . . if the light strip under the cupboard

. . . units is mounted further back,

. . . if the handle is more than 20 mm thick.

Position the template

II further back.

3. Align and screw on the enclosed

mounting rails.

Note the thickness of the sides of the

cupboard (16 mm or 19 mm).

dimension X.

If the interior depth of the cupboard is

less than 280 mm, the 250 mm high rear

panel must be removed.

x=16mm x=19mm

Installation inside the wall

cupboard

1. Remove the ﬁlter frames (see Operating

Manual).

2. If the hinges are no longer accessible

when the extractor hood has been

installed, align the cupboard doors.

3. Lift and push the extractor hood from

below into the cupboard until the

installation aids on the left and right lock

into position.

4. Pull out the ﬁlter drawer all the way.

5. Attach the extractor hood by screwing

in 2 screws on the left and right. Do

NOT tighten the screws. Raise the

extractor hood.

6. Align the extractor hood in the

cupboard and tighten the screws.

7. Feed the mains connection cable

through the aperture into the upper

cupboard and connect the pipe.

8. Connect to the power supply.

9. If required, shorten the wall cover to the

required size (e.g. saw off) and screw to

the upper cupboard.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Junker JD36AB50 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 8,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Junker JD36AB50 Manual

Product: