614573
31
Zoom out
Zoom in
Previous page
1/32
Next page
故障及解决办法
出现故障时,请先确认是否按照说明正确操作。如故障仍未排除,请按以下指南进行检查更正
故障 原因 处理方法 参考页次
跳针
1.机针弯曲或者针尖边钝。
2.机针没有正确的安装在机针把上。
·更换机针。
·从新安装机针。
22
22
机针线断开
1.机器穿线不正确。
2.机针线张力太大或太低。
3.机针弯曲或者针尖边钝。
4.所有的机针号不适合线。
·正确穿线。
·调整合适的线张力。
·更换机针。
·更换合适型号的机针。
15-17
20
22
22
梭心线断开
1.梭心线张力太大。
2.梭心罩弹簧摩擦出现缝隙。
3.针板上的机针空出现擦痕。
·减小张力。
·更换梭心罩。
·更换针板。
20
-
-
机针断裂
1.机针弯曲或没有正确安装。
2.机针碰到针板或压脚。
·更换或正确安装机针。
·纠正机针、针板或者压脚的位置。
22
-
针迹起皱
1.缝纫时压脚压力太大。
2.机针线张力于梭心线张力不平衡。
3.线与机针连接不正确。
4.机针太错。
·减小压脚压力。
·平衡张力。
·正确的连接机针和线。
·更换合适的机针。
10
20
21
21
针迹不优美 1.机针线张力于梭心线张力不平衡。 ·平衡张力。 20
或太重
1.送布牙中堆积灰尘。
2.中的使
完。
3.使用专用的缝纫机油。
4.穿线勾线上堆积有灰尘。
·对缝纫机进行保养。
·对缝纫机进行保养。
·采用合适的缝纫机使用油。
·清洁机器。
27
27
27
27
或没有声音
1.线被绕在穿线勾上。 ·线进行,用时针时针把手
动几次,然后取下缠绕在线钩上的线。
-
料口
1.针距设置为“0”。
2.下送料旋钮设置为“非送料”。
3.压脚压力太低。
·调整合适针距。
·将下送料旋钮设置为“送料”。
·转动压脚压力调节器适当增加压力。
9
10
10
无法进行机针穿线
1.机针还未被抬起。
2.插入
更远。
3.机针穿线
时),缝纫机已经随之转动。
·转动飞轮或按上/下开关以使机针处于最高位置。
·正确安装机针。
·
反)。
17
22
-
30
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Juki TL-98P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Juki TL-98P in the language / languages: English as an attachment in your email.

The manual is 7,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info