614567
29
Zoom out
Zoom in
Previous page
1/36
Next page
28
Quilting foot / Prensatelas de acolchado / Pied ouateur
This quilting foot is convenient for free motion quilting, quilting along with the pattern, free-hand embroidery, etc.
Este prensatelas de acolchado es útil para el acolchado de movimiento libre, acolchado junto con el patrón, bordado a mano alzada,
etc.
Ce pied ouateur est pratique pour le matelassage libre, le matelassage avec motifs, la broderie libre, etc.
Turn off power. Install the quilting foot. Put the plate on the needle clamp
screw, insert the installing portion into the presser bar, and securely tighten
the screw in the presser foot.
Desconecte la alimentación eléctrica. Para instalar el prensatelas de acol-
chado. Coloque la placa en el tornillo sujetador de aguja, inserte la parte
de instalación dentro de la barra prensadora, y apriete rmemente el torni-
llo en el pie prensatelas.
Mettre la machine hors tension. Installer le pied ouateur. Placer la plaque
sur la vis du pince-aiguille, insérer la partie de montage dans la barre de
presseur et serrer la vis du pied presseur à fond.
Position Feed Dog in lower position.
Ajuste el dentado de transporte a su posición inferior.
Placer la griffe d’entraînement sur sa position inférieure.
Position stitch length adjusting dial ”0”. Rotate presser foot pressure regu-
lator until green bar in pressure indication window is at top.
Posicione en “0” el cuadrante de ajuste de longitud de puntada. Gire el
regulador de presión del pie prensatela hasta que la barra verde llegue al
tope de la ventanilla indicadora de presión.
Placer le cadran de réglage de longueur des points sur “0”. Tourner le
régulateur de pression du pied presseur jusqu’à ce que la barre verte se
trouve en haut dans la fenêtre d’indication de pression.
Lower the foot and start sewing.
Baje el prensatelas e inicie el cosido.
Abaisser le pied presseur et commencer la couture.
1
4
2
3
Size / Tamaño / Taille
1/5 inch (5.0 mm)
Plate
Placa
Plaque
Screw in the presser foot
Atornillar el pie prensatelas
Vis du pied presseur
Needle clamp screw
Tornillo sujetador de aguja
Vis du pince-aiguille
1/8 inch (3.2 mm)
Presser bar
Barra prensadora
Barre de presseur
CAUTION:
Turn OFF the power switch when replacing the presser foot.
AVERTISSEMENT:
Avant de remplacer le pied presseur, placer l’interrupteur d’alimentation sur arrêt.
AVISO:
Cuando cambie el prensatelas posicione en OFF el interruptor de la corriente eléctrica.
1/4 inch (6.5 mm)
1/8 inch (3.2 mm)
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Juki TL-2010Q at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Juki TL-2010Q in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 5,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info