614765
39
Zoom out
Zoom in
Previous page
1/42
Next page
31
Before you call for help: Trouble and corre ctive measu res
serusaemevitcerroC)nosaer(esuaCTrouble Page
Presser foot pressure is too low. Increase the presser foot pres sure by turning the
presser foot pressure adjusting screw to the right.
Fabric does not
feed
10
When the trouble is not corrected by the above measures, contact your local dealer.
The followingproblems should not be regarded as the machine trouble. Check the following table before you call for help from us.
Need les break Needles are bent, or the needle point is blunt.
Needles are incorrectly attached.
The material cloth is excessively stretched.
Replace the needles.
Attach the needle correctly.
Hold the edge of the material cloth lightly with your
hand when sewing.
11
11
-
Thread breaks The machine is incorrectly threaded.
Thread tension is too high.
Needles are incorrectly attached.
Rethread the machine correctly.
Adjust the thread tention properly.
Adjust the needles correctly.
12-1 6
20,21
11
Stitch skips
Needles are bent or needle point is blunt.
Needles are incorrectly attached.
The machine is incorrectly threaded.
Replace the needles.
Attach the needle correctly.
Rethread the machine correctly.
11
11
12-1 6
Poor stitches are
for mation
Thread tension is not proper.
Adjust the thread tention properly.
20,21
Seams flute or
wave, especially
when sewing knits
Presser foot pressure is too high.
* Differential feed is set incorrectly.
Reduce presser foot pressure.
* Adjust differential feed to N - 2.
10
25
Seams pucker Thread tension is too high.
* Differential feed is set incorrectly.
Set the thread tention adjusting dial to the smaller
value.
* Adjust differential feed to 0.7 - N.
20,21
25
Motor trouble The motor makes noise.
The motor will not rotate.
Unusually large sparks are emitted.
-.hsurbnobracehtecalpeR
Voor u hulp zoekt: Problemen en oplossingen
Probleem Oorzaak Oplossing Bladzijde
De stof wordt
niet gelijk
getransporteerd
- Het differentieel transport is niet juist ingesteld.
- Naaivoetdruk is te laag.
- Onder- of bovenmes is bot of niet juist geplaatst.
- Controleer de instelling.
- Corrigeer de voetdruk.
- Plaats de messen opnieuw.
25
10
29
Draadbreuk
-De draadspanning staat te strak voor het gebruikte garen.
-De machine is niet juist ingeregen.
-De naalden zijn niet juist geplaatst.
- Verminder de spanning.
- Controleer de ingeregen draden.
- Breng de naalden volledig in in de naaldklem
met de vlakke kant naar achteren.
20-21
12-16
11
Naaldbreuk
- Naalden zijn verbogen of bot of de punt is beschadigd.
- Naalden zijn niet juist ingebracht.
- Getrokken aan de stof tijdens het naaien.
- Vervang de naalden.
- Breng de naalden volledig in in de naaldklem
met de vlakke kant naar achteren.
- Geleidt de stof voorzichtig met de beide handen.
11
11
--
Overslaan
van steken
- Naalden zijn verbogen of bot.
- Verkeerde naalden.
- Naaivoetdruk is te laag.
- Vervang de naalden.
- Gebruik Naalden Systeem 705/130H,
- Verhoog de naaivoetdruk.
11
11
10
Slechte
steekvorming
-Draden zitten niet goed in de draadspanning.
- De draad zit klem.
- De machine is niet goed ingeregen.
- Controleer of de draad tussen
de spanningsplaatjes ligt.
- Doe de naaivoet omhoog en trek aan de draad.
- Controleer het inrijgpad van elke draad.
20-21
De zoom golft
(vooral bij
gebreide stof).
- Aan de stof getrokken tijdens het naaien.
- Naaivoetspanning te hoog.
- Differentieel transport niet correct ingesteld
- Geleidt de stof voorzichtig met de beide handen.
- Zet de spanning wat lager.
Zet het transport op 0.7-N
--
20-21
25
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Juki MO-654DE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Juki MO-654DE in the language / languages: German, Dutch as an attachment in your email.

The manual is 7,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Juki MO-654DE

Juki MO-654DE User Manual - English, French, Italian, Spanish - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info