614738
47
Zoom out
Zoom in
Previous page
1/52
Next page
45
Performance Checklist
If sewing difficulties occur, make sure the instructions are correctly followed.
If a problem still exists, the reminders below may help solve it.
Specification table
Needle breaks.
Machine fails to
feed fabric.
* Machine runs idle.
* Stitch length is set at left position of manual
mode.
* Drop feed is engaged.
* Return bobbin winder to the left.
* Set stitch length at auto mode or right position
of manual mode.
* Disengage drop feed.
* Needle is bent. Needle is not correctly
installed.
* Presser foot does not match pattern
selected.
* Relation among needle, thread and fabric
is not appropriate.
* Change needle with a new one and install it
correctly.
* Use presser foot that matches the pattern
selected.
* Use needle and thread that match fabric.
Page
Thread breaks.
Bobbin thread
breaks.
Skipped stitches.
10,11
18,19
9
* Machine head is incorrectly threaded.
* Thread is caught in a part that is not to be
threaded.
* Needle thread tension is too high.
* Needle is bent.
* Re-thread machine head correctly.
* Check spool pin and thread guide for thread
tangling.
* Adjust thread tension adequately.
* Replace needle with a new one.
* Needle is not installed correctly.
* Needle is bent.
* Machine head is not correctly threaded.
* Correctly attach needle.
* Replace needle with a new one.
* Re-thread machine head correctly.
14
15
17
Puckering occurs.
Thread tangles on
wrong side of fabric.
Loud noise, heavy
to turn the handwheel.
Sewing machine will
not sew when start
button is pressed.
Needle cannot be
threaded.
* Thread tension is too high.
* Needle and thread do not match fabric.
* Adjust thread tension adequately.
* Use needle and thread that correctly match
fabric.
* Machine head is not correctly threaded. * Re-thread machine head correctly.
* Lint or dust has accumulated in hook. * Clean up hook.
* Bobbin winder is set in bobbin winding
position.
* Controller is connected to machine.
* Return bobbin winder to the left.
* Start machine with controller or remove
connector from machine.
* Needle is not raised to its highest
position.
* Needle is not installed by fully inserting
into needle clamp.
* Sewing machine is rotated by mistake with
needle threading lever lowered (during
needle threading).
* Turn handwheel to raise needle to its highest
position.
* Correctly install needle.
* Turn handwheel slightly away from you (in
direction opposite to normal direction of
rotation in which handwheel turns to perform
sewing).
12,13
-
16
14
14
14
12,13
16
17
12,13
44
10,11
8,9
13
14
-
Problem Cause (Reason) Action to be taken
Item Specification
Dimensions 410 (W) x 300 (H) x 180 (D) mm
7.3kg (when attached with case: 8.4kg)
120V / 1.0A 60Hz (USA and Canada only)
220-230V / 100W 50 / 60Hz
120V / 15W (USA and Canada only)
240V / 15W
440 (W) x 305 (H) x 215 (D) mm
Weight
Dimensions when attached
with case
Rated voltage/ Power con-
sumption
Power consumption of lamp
2003/08/21, 15:13Page 47
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Juki HZL-E61 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Juki HZL-E61 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Juki HZL-E61

Juki HZL-E61 User Manual - Italian - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info