614758
114
Zoom out
Zoom in
Previous page
1/120
Next page
112
If sewing difculties occur, make sure the instructions are correctly followed.
If a problem still exists, the reminders below may help solve it.
Case Cause (Reason) Solution
Refer-
ence
page
● The machine stops sew-
ing suddenly.
(This is in case you
can turn hand wheel by
hand.)
The machine sews at slow speed
continuously
.
(The machine has a mechanism to
automatically cut of
f the power to
prevent the motor from overheating.)
T
urn off the power and wait for a
while (about 10 minutes). The safe-
ty mechanism will be reset and the
machine will return to normal.
3
The machine will not
work even when start/
stop button is pressed.
(This is in case sewing
light is still on.)
The needle hits presser foot due to
an installation of incorrect presser
foot.
The needle fell into the hook area
and tried to start.
Use the appropriate presser foot to
the selected stitch pattern.
Remove the needle from the hook
area.
-
-
● Needle breaks. ● Thick material is sewn with a thin
needle.
● The needle is not inserted fully.
The needle setscrew is not securely
tightened.
The wrong presser foot is used for a
certain pattern.
Needle is bent.
Check the combination of fabric,
thread and needle.
Check the installation of needle.
Securely tighten the needle set
-
screw.
Check the combination of stitch
pattern and presser foot to be used.
Change needle.
27
26
26
-
26
Loud noise and/or keen
noise while sewing
Lint or dust has accumulated in the
feed dog.
Lint or dust has accumulated in the
hook.
Clean the feed dog area.
Clean the hook area.
111
111
Machine fails to feed
fabrics.
The stitch length is set at “0”.
Soft fabrics such as towels are being
sewn.
The machine is set in drop feed con
-
dition. (the drop feed knob is on the
right side)
Float-function height is excessively
high.
When the stitch pattern is reselect-
ed, the machine goes back to the
default setting.
Set the stitch length to 3 – 5.
Set the drop feed knob to left side.
Adjust the oat-function height.
43
-
29
92
Needle can not be
threaded. (This is in
case needle threader
will not turn.)
The hook of needle
threader does not go
through the needle eye.
The needle is not in the up position.
(When needle is not in the up posi
-
tion, needle threader will not turn.
This is to avoid damages to the
hook.)
The needle is not inserted fully
.
Rotate the hand wheel and lift the
needle upwards.
Check the installation of the needle.
24
26
Performance check list
114


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Juki HZL-DX5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Juki HZL-DX5 in the language / languages: English as an attachment in your email.

The manual is 42,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info