Manual JRpropo XG14 (page 14 of 112) (English)

606954

Zoom out

Zoom in

1/112

▋Binding▋Procedure▋

▋(pairing▋the▋transmitter▋and▋receiver)

In order for the transmitter and receiver to communicate, it is essential to pair or bind them together.

Please follow this procedure:

1) Be sure that remote antenna unit is properly connected

to the receiver. Locate the included bind plug, and ensure

the transmitter and receiver batteries are fully charged.

※ Note that the Remote Antenna acts as both a receiver and

also transmits data back to the transmitter. Carefully

note the orientation of the antenna within the remote

unit. This orientation is extremely important.

2) On the transmitter access the “BIND & RANGE” menu

under the System List.

RefertothePage78"BindandRangeCheck【BIND&RANGE】"

3) Inserting the bind plug into the bind terminal of the

receiver and connect the battery to a spare channel (such

as the AUX channel) - the LED’s on the receiver and the

remote antenna will begin to blink (Ready to Bind).

Note:

Be sure to insert the bind plug before connecting the

battery.

4) Refer to the “BIND & RANGE CHECK” Screen in the

transmitter System Setting mode. Press the dial to start

the binding process.

5) ‘Binding’ will flash on the transmitter display, and

upon completion of the binding process, it will display

“SUCCESS ! PLEASE CHECK FAIL SAFE”. Concurrently,

both receiver’s LED’s will stop flashing and be solid –

signifying completion of the bind process. Disconnect the

bind plug from receiver, disconnect the receiver battery

and switch o󰮏 transmitter. If the LED’s continue to blink,

repeat the procedure from the beginning.

6) Lastly, connect a servo, turn on the transmitter then

receiver, and confirm that communications have been

established.

RangeCheck

This checks the performance of the transmitter by lowering

the power output to simulate a long distance range test.

Under the” Bind & Range Check” setting screen, move the

cursor to the POWER: NORMAL column and change it to

LOW. The transmitter LED shall ash Blue to indicate it is

set to low power mode. When in this mode, walk a distance

of approximately 40m from the aircraft and conrm that the

transmitter operates the aircraft normally. Continue testing

as you walk around the aircraft.

RefertothePage78"Bind

andRangeCheck【BIND&RANGE】"

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters　　　

Connecting

the battery to a

spare channel

(such as AUX

channel)

Location of LED light

Binding terminal

Bind plug

RefertothePage89"Failsafe【FAILSAFE】"

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters　　　

Connecting

the battery to a

spare channel

(such as AUX

channel)

Location of LED light

Binding terminal

Bind plug

Preparation

XG14English.indd 12 2013/07/16 16:39

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of JRpropo XG14 in the language / languages: English as an attachment in your email.

The manual is 25,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

JRpropo XG14 Manual

Product: