28356
28
Zoom out
Zoom in
Previous page
1/148
Next page
Section 2 Installation
27
Figure 2-2
Console Mounting/ Surface Mounting
1) Select a mounting location: a clear, flat area of at least 8”(203mm) wide by 8”
high, having 5.5”(140mm) depth behind the panel. At that time, make sure
that there are no hidden electrical wires or other items behind your selected
location before proceeding.
2) Tape the mounting template from the console mounting instruction over your
selected location on the panel and trace around the edges.
3) Drill a 1/2”(12.7mm) pilot hole at the top and bottom of the cut-out area.
4) Cut along the outside edge of the cut-out line with an appropriate saw.
5) Drill holes, using a 1/5”(5mm) drill bit, for the four threaded screws, 2 on
each side, on the mounting template.
6) Remove the yoke, two knobs, two spacers and two damping rubbers from the
unit, then securely attach the threaded screws to the rear cabinet and verify
that the unit will fit inside the cut-out area.
7) Complete installation of the DC power, Scanner, GPS, NMEA and ground
wiring into the console and make the connections onto the rear of the unit.
8) Place the unit into the cut-out and fit the washers, lock-washers, onto the
threaded screws behind the mounting console, and tighten the nut to hold the
unit in place.
1 SCREW
2 NUT
3 WASHER
4 LOCK WASHER
Illustration above shows the
way of Console Mounting.
Illustration above shows the
cut-out size of the mounting
in the console.
61 (2.4)
82 (3.2)
94.5 (3.7)
65.5 (2.6)
54.5 (2.1)
4-R4 (0.2)
Unit : mm (inch)
4
(0.2)
4- 5 ( 0.2)
44.5 (1.8)
65.5 (2.6)
50 (2)
6.5 (0.3)6.5 (0.3) 191 (7.5)
45.5 (1.8)
100 (3.9)
45.5 (1.8)
4 (0.2)160 (6.3)
ATTENTION
Make sure there are no hidden electrical wires or other
items behind the desired location before proceeding.
Also check that you have free access for mounting and
cabling.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRC Radar1800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRC Radar1800 in the language / languages: English as an attachment in your email.

The manual is 2,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info