28307
262
Zoom out
Zoom in
Previous page
1/310
Next page
246
9.7 Adjustment Procedures
9.7.1 General adjustments
1. Adjustments to be made when a part is replaced
1. Adjustments to be made when a part is replaced1. Adjustments to be made when a part is replaced
1. Adjustments to be made when a part is replaced
Adjustments need to be performed when major parts of the radar unit. are replaced.
(a) When the V101 magnetron is replaced Tuning
(b) When the E101 front end is replaced Tuning
(c) When the V901 Cathod-ray tube is replaced
Off center adjustment
When the CRT monitor PCB is replaced
Brilliance level adjustment
Focus adjustment
: When exchanging V901 (CRT), the Direction coil implement in the stuck condition.
Incidentally, It is possible to arrange in cathode-ray tube monitor chassis (CKJ-159)
2. CRT monitor off center adjustment
2. CRT monitor off center adjustment2. CRT monitor off center adjustment
2. CRT monitor off center adjustment
(a) This adjustment must be performed on the centering magnet (permanent magnet)
located immediately behind the deflection coil. This permanent magnet is made up of
two doughnut-like disks.
(b) Turn the centering knob so that the neck of the Cathod-ray tube is in alignment with the
center of the PPI screen.
3. Adjusting the brilliance level of the CRT monitor screen.
3. Adjusting the brilliance level of the CRT monitor screen.3. Adjusting the brilliance level of the CRT monitor screen.
3. Adjusting the brilliance level of the CRT monitor screen.
(a) Set the brilliance level of the CRT monitor screen to its maximum from the menu.
Please refer to "3.2.1 Changing the brightness of the screen" for the method of ad-
justment.
(b) Turn potentiometer R451 on the CRT monitor PCB so that no raster appears in the
non-displayable area. (Turn the potentiometer slowly since the circuit's sensitivity is
very high.)
4. Adjusting the focus of the CRT monitor screen
4. Adjusting the focus of the CRT monitor screen4. Adjusting the focus of the CRT monitor screen
4. Adjusting the focus of the CRT monitor screen
(a) Turn potentiometer R951 on the neck PCB in the display unit so that the range rings
and video images appear most clearly.
262


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRC JMA2343 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRC JMA2343 in the language / languages: English as an attachment in your email.

The manual is 17,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info