542987
34
Zoom out
Zoom in
Previous page
1/52
Next page
STEP:1
FRONTSUPPORT(FrontStabilizer)Assy
NO PARTS LIST QUANTITY
STEP:2
REARSUPPORT(RearStabilizer)ASSY.
NO PARTS LIST QUANTITY
STEP:3
UPRIGHTTUBEASSY.TOTHEFRAME
NO PARTS LIST QUANTITY
STEP:4
PEDALASSY.
NO PARTS LIST QUANTITY
STEP:5
PEDALSUPPORTTUBEASSY.()
NO PARTS LIST QUANTITY
As photo shown
1) In order to facilitate assembly, use one of the lager styroform set
under the Frame ( as photo shown)
2) Attach the rear support to the frame with two bolts (#19)
washers (#65) nuts #20)
3) locking sleeves with tool and cover the nut with two caps (#21)
As photo shown
1) in order to facilitate assembly, use one of the lager styroform set
under the Frame ( as photo shown)
2) Attach the front support with transportation wheels to the frame with
two bolts (#19) washers (#65) nuts (#20)
3) locking sleeves with tool and cover the nut with two caps (#21)
As photo shown
1) place upright tube on top of a chair ( or by a second person to
assist holding) close to the main frame be facilitated to connect the cables.
2) check the direction of upright tube before connect the Top/Bottom
pre-assembled cables as photo shown.
3) fixing eight screws (#18) with finger locking first then tighten all firmly.
Note! tighten the two screws on the label "" screw hold and
then locking up the rest of six screws.
2
2
#21
#19 2
#65
#20
2
2
#65 2
#20 2
#21 2
#18 6
#19
#22 8
#20 8
#5 2
#12 2
#82 2
#17
2
2
1) Set both pedal tube (R#74/L#75) & plastic pedals(#52/#53)
on the floor, indentity the (R/L) match up left set (#74/#52) &
right set (#75/#53).
Note! the pedal has left/right label, check the diredtion of pedl
for front and foot protection edge of pedal as drawing shown)
2) lock up both pedals to the tube plate with screws(#22), nut (#20),
with tool socket & screw driver firmly ( as drawing showm)
Note! Three sets of holds on the tube plate, user may choice
one set to use, eash set will give one inch variation pedal
distance to select, make sure bothpedals select the same
location of holes
1) Frist, distinguish between the left/right pedal support tube
(note: check pedal support tube with left/right label)
2) Set both pedal support tube (#74&#75) to the main frame
as drawing shown first
3) Insert long bushing (#82) to the axle on main frame (disc),
then inset both pedal trube (#74&#75), insert short bushing (#83)
washer (#1 7), secure each with M10 nylon lock nut (#12)
fully tighten up
4) cover the nut with end cap (#5)
#83
JOYSPORT
www.joysport.nl7
7
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Joy Sport CT-Explorer Crosstrainer at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Joy Sport CT-Explorer Crosstrainer in the language / languages: English, Dutch as an attachment in your email.

The manual is 5,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info