467831
13
Zoom out
Zoom in
Previous page
1/20
Next page
13
4. Push in the gas control knob (B) as far as possible and
hold it in. Simultaneously, push in the ignition knob (A)
until the spark ignites the pilot flame located to the
right rear corner of the burner.
5. Continue to hold in the gas control knob for approx. 20
seconds after the pilot flame has been lit. Then let go
of the knob. It should pop back out and the pilot flame
should remain lit.
If the pilot flame goes out, repeat Steps 1-5.
If the pilot light goes out intentionally or unintention-
ally, it should not be relit within 3 minutes.
*NOTE: If the gas control knob does not pop out when
released, call for service.
**NOTE: If the pilot flame does not remain lit after several
attempts, turn the gas control knob to OFF and call for
service.
Lighting the Main Burner
1. Turn the gas control knob clockwise to the ON position,
designated by the flame icon, . .
2. Push the ON/OFF switch at the rear of the appliance to
“ON”.
NOTE: When the appliance is used for the first time,
condensation may form in the firebox. Some smoke may
also appear from the appliance during the initial hours,
due to the burning off of paint and lubrication used in
the production process. See section Odors when using the
stove for the first time.
Adjusting the Heat Setting
Heat and flame size can be adjusted by turning the regu-
lator knob (C) marked “HI, LOW”, which is located next to
the gas control knob (see fig. 23). Maximum flame size
provides maximum heat. Make sure the appliance has
been operating for at least 30 minutes before adjusting
the flame.
Turning Off the Appliance
Push the ON/OFF switch at the rear of the appliance to
OFF. The pilot flame will continue to burn. In order to
fully extinguish the appliance, push in the gas control
knob (B) (fig. 23) a little and turn clockwise to OFF, .
Do not use force.
E
A
C
D
B
Maintenance
The complete installation, which includes the gas sup-
ply, the actual appliance and the vent system, must be
inspected annually. The inspection must be carried out by
qualified service engineer.
External Maintenance
Painted products may change color after some years of
usage. The surface should be cleaned and brushed free of
any loose particles before new stove paint is applied
Clean enameled castings only when the surfaces is cold.
Enamel will stain easily when hot. Avoid using detergents
and household cleaners as these may stain or dull the
surface. A damp cloth will usually suffice. Extreme stains
may be eliminated with vinegar and baking soda. Rinse
thoroughly with cold water and wipe dry.
Figure 23. Valve Controls.
Figure 24. Burner Switch location.



13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jotul GF 400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jotul GF 400 in the language / languages: English as an attachment in your email.

The manual is 1,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info