467801

Jotul F 374 Manual

19
Zoom out
Zoom in
Previous page
1/104
Next page
19
6.4 Inspection of the fireplace
Jøtul recommends that you personally inspect your fireplace
carefully after sweeping/cleaning. Check all visible surfaces for
cracks. Also check that all joints are sealed and that the gaskets
are in the correct position. Any gaskets showing signs of wear or
deformation must be replaced.
Thoroughly clean the gasket grooves, apply ceramic glue
(available from your local Jøtul dealer), and press the gasket well
into place. The joint will dry quickly.
6.5 Exterior maintenance
Painted products may change colour after several years usage. The
surface should be cleaned and brushed free of any loose particles
before new paint is applied.
7.0 Service
Warning! Any unauthorised change to the product is illegal.
Only use original spare parts.
7.1 Replacing the baffle/exhaust
deflector
(N.B. If you use tools, be aware that the vermiculite plates may
be damaged by rough treatment).
1. Lift up the front edge of the baffle plate and tilt it out
(fig. 29 G). Remove the side burn plates (fig. 29 F) and the
rear burn plate (fig. 29 E).
2. The exhaust deflector, in cast-iron - that is located above the
baffle plate, rests with the bar on the ribs at the rear flue
outlet (fig. 26 A). Lift the exhaust deflector slightly up, pull it
forward and tilt it out.
3. For reassembly follow the same procedure for installation,
but in reverse.
7.2 Replacement of burn plates/base
plate
(N.B. If you use tools, be aware that the vermiculite plates may
be damaged by rough treatment).
1. Lift up the front edge of the baffle plate and tilt it out. Remove
the side burn plates (fig. 29 F) and the rear burn plate (fig. 29 E).
2. Then lift up the grate and the base plate and take it out (fig.
29 D).
3. Follow the same procedure for installation, but in the opposite
sequence.
4. When reassembling the grate and the base plate, make sure
that the riddling bar (fig. 27 A) that moves the riddling grate
is threaded into the slot on the right edge of the grate.
7.3 Replacing the inner/outer side
glass
1. Lift up the front edge of the baffle plate and tilt it out Remove
the side burn plates (fig. 29 F) and the rear burn plate (fig. 29 E).
2. The exhaust deflector, in cast-iron - that is located above the
baffle plate, rests with the bar on the ribs at the rear flue
outlet (fig. 26 A). Lift the exhaust deflector slightly up, pull it
forward and tilt it out.
3. Remove riddling grate, base plate and ash pan (fig. 29 D).
Fig. 31
Fig. 32
4. Unscrew the upper and lower screws (fig. 31 A and 32 A), and
tilt the glass holder with the glass carefully out through the
door. N.B. The glass holder also keeps the outer glass in place
5. Remove the glass and possibly replace gaskets. If needed
replace the external glass.
6. For reassembly follow the same procedure for installation,
but in reverse.
ENGLISH
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jotul F 374 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jotul F 374 in the language / languages: English, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info